Gewiss CHORUS GWA9531 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 57

Gewiss CHORUS GWA9531 Скачать руководство пользователя страница 52

52



Output- Presence (n.31)

This object is used to report the presence on HVAC 2 channel.

The enabled flags are C (communication), R (read by bus) and T (Trasmission).
The standard format of the object is 1.001 DPT_Switch.
The standard format of the object is

1 bit and the information it contains is

“On/Off”.



Input- Locking object (n.32)

This object is used to block the HVAC 3 channel.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 1.010 DPT_Switch.
The standard format of the object is

1 bit and the information it contains is

“Start/Stop”.



Input- External influence (n.33)

This object is used to receive external control of the HVAC 3 channel.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 1.001 DPT_Switch.
The standard format of the object is

1 bit and the information it contains is

“On/Off”.



Input- Follow time in minutes (n.34)

This object is used to set follow time on HVAC 3 channel.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 7.006 DPT_TimePeriodMin.
The standard format of the object is

2 byte and the information it contains is

”VALUE

(min)”



Input- Overwrite threshold (n.35)

This object is used to overwrite threshold on HVAC 3 channel.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 9.004 DPT_Value_Lux.
The standard format of the object is

a 2 byte and the information it contains is

“Value_lux”.



Input-Switch on upon movement (n.36)

This object is used to set automatic mode or semy-automatic on HVAC 3 channel.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 1.003 DPT_Enable.
The standard format of the object is

1 bit and the information it contains is

“enable/disable”.



Output- Presence (n.37)

This object is used to report the presence on HVAC 3 channel.
I flag abilitati sono C (communication), W (written by bus) and T (trasmission).
The standard format of the object is 1.001 DPT_Switch.
The standard format of the object is 1 bit and the information it contains is

“On/Off”.

«
...
50
51
52
53
54
...
»

Содержание CHORUS GWA9531


























































Отзывы:

Нет отзывов