GEV FlammEx FMG 30008, Руководство пользователя

Страница: 6 / 18

Technical information
Model name FMG 3255: model B
FMG 30008, FMG 30015: model A
Battery operation 3 x 1.5 V alkaline (AA/Mignon) Energizer E91
Certification EN 50291-1: 2010
Signal volume approx. 85 dB/3 m
Storage/transport temperature +4°C - +38°C
Permissible air humidity 10% - 95%, non-condensing
Protection type IP X2D
Dimensions Ø 125 mm, height 33 mm
Service life of detector approx. 5 years
10 11
Battery and rechargeable battery information
Old batteries may not be disposed of with the unsorted household waste. Owners of used batteries
are legally obliged to recycle the batteries and can return them free of charge to the point of sale.
Batteries contain materials which are harmful to the environment and health, and must therefore be
disposed of professionally.
Recycling instructions
This device must not be disposed of with unsorted household waste. Owners of old devices are
required by law to dispose this device correctly properly Contact your town council for further
information.
CO concentration in air No. minutes before alarm triggered
50 ppm 60 - 90
100 ppm 10 - 40
300 ppm 3
Trigger level in accordance with EN 50291-1 : 2010
Table of functions:
Sound Green Power LED Red Alarm LED Yellow Fault LED Meaning
none flashes every 60secs off off normal function
beeps every 60 secs off off flashes every battery low, see Maintenance
60 secs
beeps every 60 secs off off constantly lit alarm is not locked into
after approx. 6 minutes mounting plate
beeps every 2 secs flashes every 2 secs flashes every 2 secs flashes every 2 secs test function
beeps every 60 secs off off flashes 3 x device faulty, replace
every 60 secs immediately
beeps every 60 secs flashes every 60 secs flashes off muted
intermittent off flashes off alarm triggered, see What to do
when the alarm sounds
none flashes approx. flashes approx. off warm-up phase of approx.
every 8 secs every 8 secs 5 minutes after switch-on
Maintenance
Changing the battery
The batteries should be changed at least once a year or immediately if the low battery alert sounds. When
changing the batteries, the alarm must not be dismounted.
1. Open the battery compartment (Fig. 8A) while at the same time sliding the compartment cover downwards
(Fig. 8B) . Do not dispose of the batteries with your household waste. You must recycle all used batteries.
Batteries may be returned free-of-charge to the point of sale or to your local collection point.
2. Insert 3 new batteries correctly (Fig. 9) and make sure that the red pins are in contact with each battery.
The alarm confirms that the batteries are in place with a short sound.
3. Close the battery compartment by placing the cover on the alarm and sliding it upwards until it pops in.
4. Test the alarm right away ( see Operating test ).
We recommend the following 1.5 V alkaline batteries, size AA/Mignon Energizer E91.
Under normal conditions new batteries will last for around a year – depending on the number of tests. If
the alarm is subjected to high or low temperatures for longer time, or to high air humidity, battery lifetime
will reduced.
Testing the alarm
Check once a week that the alarm is working properly by briefly pressing down the Test/Mute button
(Fig. 8B) . The alarm will beep 2 or more times and the 3 LEDs (Fig. (C) will light up briefly. Afterwards the
alarm returns to its normal operating mode.
Cleaning the alarm
Loose dust inside the alarm can be through the vents using a vacuum cleaner. The alarm cover can be
cleaned from the outside with a lightly dampened cloth. Under no circumstances use of any detregent
containing ammonia or any other chemicals (such as cleaning agents or solvents) on or anywhere near the
alarm. Do not paint or varnish the alarm!
Alarm functions
The alarm is equipped with a battery monitoring system. Low batteries are indicated by the alarm starting
to beep and the yellow Fault LED (Fig. (C) flashing around every 60 seconds. The alarm will continue to
work in this condition for around another 7 days. You should nevertheless change the batteries as soon
as possible. In the event of an alarm, the device can be muted by briefly pressing the Test/Mute button
(Fig. 8B) .
Subject to technical and design changes without prior notice.
DE
GB
FR
IT
PL
CZ
S
LO
SK