GESTRA NRR 2-50 Скачать руководство пользователя страница 31

Страница: 31 / 36

NRR 2-50, NRR 2-51 - USA - Installation & Operating Manual -

850699-00

Attention

Please check the following before fault diagnosis:

Supply voltage:

Is the level switch supplied with the voltage specified on the rating plate?

Wiring:

Does the wiring conform to the wiring diagram?

Fault indications and troubleshooting

Indications, diagnosis and corrective action

Attention

■

For further troubleshooting, please refer to the NRGT 26-2 Installation & Operat-

ing Manual.

In the event of a level controller malfunction, the MIN and MAX alarm is triggered

and the equipment restarts.

If the process repeats itself continuously, the equipment must be replaced.

Note

Error codes on the 7-segment display

Error code

Error

Corrective action

E.005

Faulty level transmitter, measuring current

< 4 mA

Check level transmitter and replace if neces-

sary. Check electrical connection.

E.006

Faulty level transmitter, measuring current

> 20 mA

Check level transmitter and replace if neces-

sary. Check electrical connection.

E.013

MIN switchpoint higher than MAX switch-

point

Reset switchpoints

In the event of a malfunction, the MIN and MAX alarm is triggered.

Action against high-frequency interference

Further information

High-frequency interference can be caused by out-of-phase switching operations. If such in-

terference occurs and results in sporadic failure, we recommend taking the following action to

suppress interference:

■

Provide inductive loads with RC combinations as specified by the manufacturer.

■

Route the connecting cable to the level electrode or level transmitter separately from power

lines.

■

Increase the distance from sources of interference.

■

Check the connection of the shield to the central grounding point (CGP) in the control cabinet.

■

Suppress HF interference using hinged-shell ferrite rings.

Содержание NRR 2-50





































Результаты поиска

Содержание NRR 2-50

Отзывы:

Похожие инструкции для NRR 2-50

Бренды по названию

Популярные бренды

GESTRA NRR 2-50, Оригинальное руководство по установке и эксплуатации

Результаты поиска

Содержание NRR 2-50

Отзывы:

Похожие инструкции для NRR 2-50

Бренды по названию

Популярные бренды