GESTRA NRR 2-50 Скачать руководство пользователя страница 27

Страница: 27 / 36

NRR 2-50, NRR 2-51 - USA - Installation & Operating Manual -

850699-00

Starting

Action

Indication

Function

Switch on supply

voltage. Water level

between MIN and

MAX.

7-segment display shows

software and equipment

version

System test, takes approx. 3 s.

7-segment display shows

actual value

System switches to operating mode

Setting parameters

Action

7-segment display

Function

Turn rotary knob until

desired parameter is

shown

Display toggles between

parameter and saved value.

The parameter is selected

Press and hold the

push-button (on rotary

knob)

First digit (000

) flashes.

Parameterization mode active. You can change

the first digit.

Turn rotary knob

A new value is displayed.

Turning clockwise increases the value, turning

anti-clockwise reduces the value.

Briefly press push-

button

2nd, 3rd or 4th digit flashes.

(from right to left)

2nd, 3rd or 4th digit can now be changed using

the rotary knob. Turning clockwise increases the

value, turning anti-clockwise reduces the value

When your entries are

complete: press and

hold the push-button

within 3 s.

done is briefly displayed.

Next, the display toggles

between the parameter and the

new value.

Your entry is confirmed. System switches back

to the

parameter.

If you do not confirm

your entry within 3 s

or you do not make

any further entries:

quit is briefly displayed.

After this, the display toggles

between the parameter and the

old value.

If you do not confirm, your entries will not be

applied. Please repeat the procedure. If you do

not confirm, the system switches back to the

parameter.

Turn the rotary knob until the next parameter is shown.

Or turn the rotary knob until the actual value is displayed.

Or after 30 s, the actual value is displayed automatically.

Bringing into service

Setting parameters

Fig. 8

Valve

opens

MAX

LED

red
MIN

LED

red

Rotary knob

with

integrated

push-button

OO75

7-seg-

ment

display

Valve

closes

Yellow

LED

Содержание NRR 2-50





































Результаты поиска

Содержание NRR 2-50

Отзывы:

Похожие инструкции для NRR 2-50

Бренды по названию

Популярные бренды

GESTRA NRR 2-50, Оригинальное руководство по установке и эксплуатации

Результаты поиска

Содержание NRR 2-50

Отзывы:

Похожие инструкции для NRR 2-50

Бренды по названию

Популярные бренды