Geokon 4500AL Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 39

Geokon 4500AL Скачать руководство пользователя страница 22

16

4.6 Splicing and Junction Boxes

Because the vibrating wire output signal is a frequency rather than a current or voltage,
variations in cable resistance have little effect on gage readings. Therefore, splicing of cables has
no effect, and in some cases may in fact be beneficial. For example, if multiple piezometers are
installed in a borehole, and the distance from the borehole to the terminal box or datalogger is
great, a splice (or junction box) could be made to connect the individual cables to a single multi-
conductor cable. (See Figure 8.) This multi-conductor cable would then be run to the readout
station. For these types of installations it is recommended that the piezometer be supplied with
enough cable to reach the installation depth, plus extra cable to pass through drilling equipment
(rods, casing, etc.).

Cable used for making splices should be a high quality twisted pair type, with 100% shielding
and an integral shield drain wire.

When splicing, it is very important that the shield drain

wires be spliced together.

Splice kits recommended by Geokon incorporate casts which are

placed around the splice and then filled with epoxy to waterproof the connections. When
properly made, this type of splice is equal or superior to the cable itself in strength and electrical
properties. Contact Geokon for splicing materials and additional cable splicing instructions.

Junction boxes and terminal boxes are available from Geokon for all types of applications. In
addition, portable readouts and dataloggers are also available. Contact Geokon for specific
application information.

Figure 8 - Typical Multi-Piezometer Installation

«
...
20
21
22
23
24
...
»

Содержание 4500AL








































Отзывы:

Нет отзывов