
12
Parallelism calibration of circular bubble axis to
vertical axis
Put the instrument on the tripod plate and
centralize the bubble by foot screw. Rotate the
instrument by 180°. If the bubble is still in the
center, it indicates that the circular bubble is in
the right place. If the bubble deviates the center,
it indicates that the circular bubble axis is in a
wrong place and needs to be calibrated. The
calibration method is as follows:
Turn the foot screws to move the bubble to the
center of circle. The displacement is half of the
distance from bubble to the center.
Adjust the Adjusting Screw 8 of bubble to
move the bubble to the center of circle.
Calibrate repeatedly by above method until the
bubble doesn’t offset along with turning of the
telescope.
Leveling calibration of telescope collimation axis
(calibration of i angle)
The leveling calibration of telescope collimation
axis (calibration of i angle) can be carried out
according to national leveling specification, and
also can be carried out as follows. Choose a cer
-
tain distance of 61.8m in a flat field and divide
it into 3 equal sections shown as Figure 4. Put
the instrument at Site C and Site D and put the
same staff at Site A and Site B successively. Put
the instrument at Site C firstly and obtain staff
readings a1 and b1. Then put the instrument at
Site D and obtain staff readings a2 and b2. If d
= (a2 - b2 ) – (a1 - b1)≤±2.5mm, the error of
i angle is within the allowable range. Otherwise
the collimation axis needs calibration. The me
-
thod is as follows:
(i) Calculation: d = (a2- b2 ) – (a1 - b1)
a3 = a2 – d
Calibrarea paralelismul axei bule circulară a
axa verticală.
Puneți instrumentul pe placa trepied și centralizati bula
de șurubul de jos. Rotiți instrumentul de 180 °. Dacă
bula este încă în centru, indică faptul că bula circulară
este în locul potrivit. Dacă bula deviază de centru,
aceasta indică faptul că axa bula circulară este într-o
alta pozitie și este nevoie să fie calibrat.
Metoda de calibrare este după cum urmează:
Rotiți șuruburile cu picior pentru a muta bula la
centrul cercului. Deplasati doar jumătate din
distanța între bule si centru.
Reglați șurubul de reglare 8 al bulei pentru a
muta bula la centrul cercului.
Calibrati în mod repetat, prin metoda de mai sus, până
cand bula se compensează, împreună cu intoarcerea
telescopului
Calibrare nivelare colimare telescop axa (etalonarea i
unghi) poate fi efectuată în conformitate cu specificațiile
naționale de nivelare, și de asemenea, poate fi
efectuată după cum urmează. Alegeți o anumită
distanta de 61.8m într-un domeniu apartament și
decalajul în 3 secțiuni egale prezentat ca Figura 4. pune
instrumentul de la site-ul C și site-D și a calculati:
același personal la site-ul A și B Site succesiv. pune
instrumentul de la site-ul personal C, în primul rând și
de a obține
lecturi A1 și B1. Apoi pune instrumentul la
Site-ul D și de a obține personal lecturi a2 și b2. În
cazul în care d
= (A2 - b2) - (A1 - B1) ≤ ± 2,5 mm, eroarea de
Am unghi este în intervalul admisibil. altfel
axa collimation are nevoie de calibrare.metoda
este după cum urmează:.