Genvex Optima 300 DESIGN Скачать руководство пользователя

Страница: 5 / 24

Optima 300

3. Start-up

The first time the device is started, the control panel

display will show: “Choose language”.

Click “Next” to switch between Danish, English, German

and French.

Press “Enter” when the desired language is shown in the

display.

The control panel will now read the current program

version in the selected language according to the IC

circuit’s version on the main circuit board in the device.

The display will now show:

•

Updating model

•

Wait 1.5 minutes (It takes approximately

1.5 minutes to read the

current version)

•

Language load (91)

•

Language

•

Menu load

(84)

•

Icon load

(369)

•

Reset to default

•

Restarting……..

•

Optima 300

Then the display will then change to:

•

The symbol Bookmark

•

Optima 300

•

Version number

D (Display): 1.0

C (Controller): 3.0

Finally, the display changes to daily operation and the

device is now in operation with the default settings.

The menu items can now be set as desired for the house

in question and will thereby achieve the most optimal and

most effective utilisation and operation of the device.

Содержание Optima 300 DESIGN

























Результаты поиска

Содержание Optima 300 DESIGN

Отзывы:

Похожие инструкции для Optima 300 DESIGN

Бренды по названию

Популярные бренды

Genvex Optima 300 DESIGN, Руководство пользователя

Результаты поиска

Содержание Optima 300 DESIGN

Отзывы:

Похожие инструкции для Optima 300 DESIGN

Бренды по названию

Популярные бренды