background image

Rev A

 

Instructions

 

 Procedure 

 

 

Part No. 1258800

 

Software Update 

 

Procedure 

Note: Perform this procedure on a flat level surface, 
with the boom and jib in the stowed position. 

Software Version 

Note: Before proceeding, verify the version of 
software installed on your machine.

 

1

 

At the TCON, turn the key switch to ground 
controls and pull out the red Emergency Stop 
button. 

2

 

Read and record the scroll message on the 
display (example: VER 2_10 is version 2.10). 

3

 

Push in the red Emergency Stop button. 

Limit Switch Rework 

For machines equipped with platform overload 
protection and software version less than 3.00

 

The platform overload limit switch LSP1OLS must 
be replaced before proceeding with the software 
upgrade. 

Calibration Information 

After the installation of the Application Software is 
complete, the machine will have to go through a 
complete calibration process. Refer to the 
appropriate Service Manual for your machine. 

Loading the Software onto a 
Computer or Laptop 

Note: Loading software onto your computer 
requires that you must have administrative 
rights to download executable files.

 

1

 

Turn on the computer or laptop. 

Note: If the WebGPI Software Update Zip files 
have been downloaded from the Firmware site, 
continue to the Application Software Installation. 

2

 

Insert the thumb drive (Genie part 
number 1258799) into the computer or laptop. 

Note: If the WebGPI Update files are not displayed 
on your computer, go to 

My Computer

 and locate 

the 

Removable Disk

3

 

Select each of the three application files one at 
a time. 

 

Содержание Z-135/70

















Отзывы: