Genie S-80 XC Скачать руководство пользователя

Страница: 63 / 73

First Edition • Second Printing

Operator's Manual

Transport and Lifting Instructions

Part No. 1279298GT

-80 XC

™

• S

-85 XC

™

Securing to Truck or Trailer for
Transit

Always use the turntable rotation lock pin each time
the machine is transported.

Turntable rotation lock pin

Turn the key switch to the off position and remove
the key before transporting.

Inspect the entire machine for loose or unsecured
items.

Securing the Chassis

Use chains of ample load capacity.

Use a minimum of 6 chains.

Adjust the rigging to prevent damage to the chains.

For diagram, refer to the Lifting Instructions.

Securing the Platform – S-80 XC

Make sure the platform is in the stowed position.

Secure the platform with a nylon strap placed
parallel to the strap guides. Do not use excessive
downward force when securing the boom section.

Securing the Platform – S-85 XC

Make sure the jib and platform are in the stowed
position.

Secure the platform with a nylon strap placed
parallel to the strap guides. Do not use excessive
downward force when securing the boom section.

Содержание S-80 XC










































































Результаты поиска

Содержание S-80 XC

Отзывы:

Похожие инструкции для S-80 XC

Бренды по названию

Популярные бренды

Genie S-80 XC, Руководство оператора

Результаты поиска

Содержание S-80 XC

Отзывы:

Похожие инструкции для S-80 XC

Бренды по названию

Популярные бренды