Genie S-80 XC Скачать руководство пользователя

Страница: 37 / 73

First Edition • Second Printing

Operator's Manual

Inspections

Part No. 1279298GT

-80 XC

™

• S

-85 XC

™

At the Platform Controls

Test Emergency Stop

Enter the platform and pull out the red
Emergency Stop button. Start the engine.

Push in the platform red Emergency Stop
button to the off position.

Result: The engine should shut off and no
functions should operate.

Pull out the red Emergency Stop button and
restart the engine.

Test the Horn

Press the horn button.

Result: The horn should sound.

Test the Foot Switch

Push in the platform red Emergency Stop
button to the off position.

Pull out the red Emergency Stop button to the
on position and do not start the engine.

Press down the foot switch and attempt to start
the engine by moving the start toggle switch to
either side.

Result: The engine should not start.

Do not press down the foot switch and restart
the engine.

Result: The engine should start.

Do not press down the foot switch and test
each machine function.

Result: No functions should operate.

Test the Tilt Sensor Alarm

Move a toggle switch, such as the engine idle
select switch.

Result: The alarm should sound at the platform
controls.

Содержание S-80 XC










































































Результаты поиска

Содержание S-80 XC

Отзывы:

Похожие инструкции для S-80 XC

Бренды по названию

Популярные бренды

Genie S-80 XC, Руководство оператора

Результаты поиска

Содержание S-80 XC

Отзывы:

Похожие инструкции для S-80 XC

Бренды по названию

Популярные бренды