Genie S-80 XC Скачать руководство пользователя | Manualshive

Страница: 14 / 73

background image

Operator's Manual

First Edition • Second Printing

Work Area Safety

12 S

®

-80 XC

™

• S

®

-85 XC

™

Part No. 1279298GT

Work Area Safety

Electrocution Hazards

This machine is not electrically insulated and will
not provide protection from contact with or
proximity to electrical current.

Obey all local and
governmental regulations
regarding required
clearance from electrical
power lines. At a minimum,
the required clearance
contained in the chart
below must be followed.

Line Voltage

Required Clearance

0 to 50KV

3.05 m

50 to 200KV

4.60 m

200 to 350KV

6.10 m

350 to 500KV

7.62 m

500 to 750KV

10.67 m

750 to 1000KV

13.72 m

Allow for platform movement, electrical line sway or
sag, and beware of strong or gusty winds.

Keep away from the
machine if it contacts
energized power lines.
Personnel on the ground
or in the platform must not
touch or operate the
machine until energized
power lines are shut off.

Do not operate the machine during lightning or
storms.

Do not use the machine as a ground for welding.

Tip-over Hazards

Occupants, equipment and materials shall not
exceed the maximum platform capacity for the
restricted or unrestricted range of motion.

Maximum platform capacity
Unrestricted range of motion

300 kg

Maximum occupants

2

Maximum platform capacity
Restricted range of motion

454 kg

Maximum occupants

3

If the platform load is greater than 300 kg, do not
move the platform into the unrestricted range of
motion zone.

Do not exceed the maximum platform capacity.

Do not attach a platform rated at 300 kg
(unrestricted range of motion) or 454 kg (restricted
range of motion) to machines with any other rated
load. See the serial label for the maximum rated
load.

The weight of options and accessories such as
pipe cradles and welders will reduce the rated
platform capacity, and must be subtracted from the
platform capacity. See the decals with the options
and accessories.

If using accessories, read, understand and obey
the decals, instructions and manuals with the
accessory.

«
...
12
13
14
15
16
...
»

Содержание S-80 XC










































































Отзывы:

Нет отзывов

Похожие инструкции для S-80 XC

Бренд: BendPak Страницы: 35

Бренд: Vestil Страницы: 6

Бренд: Mec Страницы: 56

Бренд: Mec Страницы: 260

Бренд: Skyjack Страницы: 85

Бренд: Skyjack Страницы: 98

3215 SJIII Compact Series

Бренд: Skyjack Страницы: 104

Бренд: Skyjack Страницы: 114

Бренд: Skyjack Страницы: 177

Бренд: Aichi Страницы: 56

Бренд: JLG Страницы: 202

Бренд: Oshkosh Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды