Genesis GVP 07 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 52

background image

© 2019 Genesis Attachments, LLC

Genesis GVP 07 15

!

WARNING

Using your Genesis attachment in unauthorized applica-

tions may create an unsafe situation and will void the war-

ranty.

Process Material Safely

• Do not process hardened steel material such as tool steel, railroad rail, axles or machined

parts. Hardened material breaks, rather than shears, which may cause flying debris. It will also

cause damaging decompression spikes to your Genesis attachment and base carrier hydrau-

lic systems.

• Do not operate any functions of the carrier while cutting or crushing with your Genesis attach-

ment, including boom and drive functions.

• Do not pull down structures with your Genesis attachment. Doing so may cause falling debris

or material may break free and exceed the capacities of the carrier, causing a tipping hazard.

• The rotator should only be used for positioning your Genesis attachment. Do not use the rota-

tor to pry or break material.

Lift the Load Safely

• The hydraulic system has been preset and tested by your dealer. Do not alter hydraulic set-

tings without consulting an authorized Genesis dealer or the Genesis Service Department.

Doing so will void the warranty and may cause structural damage, accidents or tipping.

• Make sure the load is held securely in the jaws. Do not move a loaded attachment if load is

loose or dangling. Make sure the load is pinched between the jaws – never cradle a load.

• For greater stability, knuckle the attachment to bring the load closer to the center of rotation

(center of gravity) while lifting. Use extra caution during reaching to avoid tipping.

Place the Load Safely

• Do not move the attachment, or anything held in the jaws, over people, equipment or build-

ings. Place the load gently. Do not throw or drop the contents.

• Operate the controls smoothly and gradually. Jerky controls are hazardous and may cause

damage to the carrier.

•

Avoid fire hazards. Keep the area clean. Remove all flammable materials from the area during

any welding or heating process. Have a fire extinguisher nearby and know how to use it.

• Never substitute pins or bolts. Use factory supplied pins. Replace all bolts with the same size

and grade. Failure to do so may cause serious injury or death.

• Use your Genesis attachment only as directed in this manual. Do not use the attachment to lift

and move other objects. Doing so may cause instability and tipping.

OPERATIONAL SAFETY

«
...
13
14
15
16
17
...
»

Содержание GVP 07





















































Отзывы:

Нет отзывов

Похожие инструкции для GVP 07

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: MacDon Страницы: 2

Бренд: MacDon Страницы: 214

Бренд: MacDon Страницы: 32

Бренд: Fellowes Страницы: 20

Бренд: LA Audio Страницы: 9

Бренд: PARUS Страницы: 6

Бренд: Rational Страницы: 16

Бренд: Tanaka Страницы: 20

Бренд: Tandem Страницы: 80

Бренд: Tanco Страницы: 4

Бренд: V-TAC Страницы: 13

Бренд: Yamaha Страницы: 29

FUSION APOLLO MS-WB675

Бренд: Garmin Страницы: 18

Бренд: Rapid Shape Страницы: 12

MultiFill 003-561-005

Бренд: Hanskamp Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды