General AOH13PNCC Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 21

General AOH13PNCC Скачать руководство пользователя страница 14

En-13

●

Before cleaning the air conditioner, be sure to turn it off and disconnect the power supply cord.

●

Be sure the intake grille (Fig. 1

1

) is installed securely.

●

When opening, closing or removing the intake grille, be cautious to prevent it from falling down.

●

When removing and replacing the air filters, be sure not to touch the heat exchanger, as per-
sonal injury may result.

CLEANING AND CARE

CAUTION!

Cleaning the Intake Grille

1. Stop the operation with the remote con-

trol and disconnect the power supply cord.

2. Remove dust with a vacuum cleaner; wipe

the unit with warm water, then dry with a
clean, soft cloth.

●

Do not remove the intake grille. Removing by force will
lead to damage.

●

Do not move the panel by hand. Moving by force will
lead to damage. Dew may condense and water may drop
near the outlet port.

●

Do not place anything on or inside the panel, this will
lead to damage.

2. Remove dust with a vacuum cleaner or by

washing.

After washing, allow to dry thoroughly in a shaded place.

3. Replace the Air Filter and close the Intake

Grille.

Align the sides of the Air Filter with the panel, and
push in fully, making sure the two lower tabs are
returned properly to their holes in the panel.

4. Close the Intake Grille.

Press on the four locations at the bottom of the grille to
securely close the intake grille. If the intake grille is not
closed securely, the temperature monitor will display a

and the operation of the air cleaning unit will be

stopped.

●

Dust  can  be  cleaned  from  the  Air  Filter  either  with  a
vacuum  cleaner,  or  by  washing  the  filter  in  a  solution
of  mild  detergent  and  warm  water.  If  you  wash  the
filter, be sure to allow it to dry thoroughly in a shady
place before reinstalling.

●

If dirt is allowed to accumulate on the Air Filter, air flow
will be reduced, lowering operating efficiency and
increasing noise.

●

During periods of normal use, the Air Filters should be
cleaned every two weeks.

CAUTION

Do not stand on any unstable table when clean-
ing. This may lead to injury resulting from falling
down.

●

If the intake grille is closed after finishing the work, the
open panel will remain open. In this case, connect the
power supply cord to the socket when the intake grille is
closed. The open panel will close.

Cleaning the Air Filter

1. Open the intake grille, and remove the air

filter.

Lift up the air filter’s handle, disconnect the two lower
tabs, and pull out.

Handle

Tabs

Handle

Tabs

Все каталоги и инструкции здесь:

http

:

//splitoff.ru/tehn-doc.html

«
...
12
13
14
15
16
...
»

Содержание AOH13PNCC






















Отзывы:

Нет отзывов