General International 75-050T M1 Скачать руководство пользователя | Manualshive

Страница: 6 / 22

background image

ELECTRICAL REQUIREMENTS

GROUNDING INSTRUCTIONS

In the event of an electrical malfunction or short circuit,
grounding reduces the risk of electric shock. The motor
of this machine is wired for 110V single phase operation
and is equipped with a 3-conductor cord and a 3-
prong grounding plug

to fit a grounded type recep-

tacle

. Do not remove the 3rd prong (grounding pin)

to make it fit into an old 2-hole wall socket or extension
cord. If an adaptor plug is used

, it must be attached

to the metal screw of the receptacle.

Note: The use of an adaptor plug is illegal in some
areas. Check your local codes. If you have any doubts
or if the supplied plug does not correspond to your elec-
trical outlet, consult a qualified eletrician before pro-
ceeding.

CIRCUIT CAPACITY

Make sure that the wires in your circuit are capable of
handling the amperage draw from your machine, as
well as any other machines that could be operating on
the same circuit. If you are unsure, consult a qualified
electrician. If the circuit breaker trips or the fuse blows
regularly, your machine may be operating on a circuit
that is close to its amperage draw capacity. However, if
an unusual amperage draw does not exist and a
power failure still occurs, contact a qualified technician
or our service department.

BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS
WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE WITH GREATER VOLTAGE THAN NEEDED CAN
RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE TO THE MACHINE. IF IN DOUBT, CONTACT A QUALIFIED ELECTRICIAN
BEFORE CONNECTING TO THE POWER SOURCE.

THIS TOOL IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS.

EXTENSION CORDS

If you find it necessary to use an extension cord with your
machine, use only 3-wire extension cords that have 3-
prong grounding plug and a matching 3-pole recepta-
cle that accepts the tool’s plug. Repair or replace a
damaged extension cord or plug immediately.

Make sure the cord rating is suitable for the amperage
listed on the motor I.D. plate. An undersized cord will
cause a drop in line voltage resulting in loss of power
and overheating. The accompanying chart shows the
correct size extension cord to be used based on cord
length and motor I.D. plate amp rating. If in doubt, use
the next heavier gauge. The smaller the number, the
heavier the gauge.

TABLE - MINIMUM GAUGE FOR CORD

AMPERE

RATING

TOTAL LENGTH OF CORD IN FEET

110 VOLTS

25 FEET

50 FEET

100 FEET

150 FEET

220 VOLTS

50 FEET

100 FEET

200 FEET

300 FEET

AWG

< 5

------->

18

16

16

14

6 TO 10

------->

18

16

14

12

10 TO 12

------->

16

16

14

12

12 TO 16

------->

14

12

* NR

* NR

* NR = Not Recommended

6

«
...
4
5
6
7
8
...
»

Содержание 75-050T M1























Отзывы:

Нет отзывов

Похожие инструкции для 75-050T M1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды