manualshive.com logo in svg

General International 75-050T M1, Руководство по установке и эксплуатации

Поделиться
Скачать
General International 75-050T M1 Скачать руководство пользователя страница 15

1.

While holding the head, loosen the two bolts 

,

using a 17 mm wrench.

- To set the head 30° left:

Tilt the head towards the left until the tilting 
bracket rests against the left 30° stop 

.

- To set the head 30° right:

Pull the stop pin 

out, then tilt the head 

towards the right until the tilting bracket rests 
against the 30° right stop 

, then release 

the stop pin.

- To set the head back to 0°:   

Pull the stop pin 

out, then tilt the head 

towards the center until the tilting bracket rests 
against the 0° stop 

, then release the stop 

pin .

- To set the head to any other angle:

To use a setting other than 0° or 30°, refer to the 
head tilt angle indicator 

to set the angle of 

the head to the desired position.

2.

Re-tighten the two bolts 

to secure the head in 

position.

HEAD TILT ADJUSTMENT

The head can be tilted to any angle from 0° to 30° to the
left or right, to allow for bevel (or angle) mortise cutting.

15

ADDITIONAL ADJUSTMENTS

For special applications such as taller workpieces (requiring off table mortising) or for angled mortises, the follow-
ing machine adjustments can also be made.

1.

Loosen the two ratchet levers 

.

2.

Slightly tighten the ratchet lever 

.

HEAD HEIGHT ADJUSTMENT

REAR VIEW

3” max

MAKE SURE THE MORTISER HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY 
ADJUSTMENTS.

3.

Manually pull the head 3” up (approx.) 

.

4.

Loosen ratchet lever 

and tighten ratchet levers 

to secure the head in position.

To raise the height of the head and extend the working capacity of the mortiser (if needed) by up to 3”:

Содержание 75-050T M1























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды