General International 75-050T M1 Скачать руководство пользователя | Manualshive

Страница: 2 / 22

background image

THANK YOU

for choosing this General

®

International model 75-050T M1 5/8”

tilting head hollow chisel mortiser. This mortiser has been carefully tested and inspected before
shipment and if properly used and maintained, will provide you with years of reliable service.
To ensure optimum performance and trouble-free operation, and to get the most from your
investment, please take the time to read this manual before assembling, installing and operat-
ing the unit.

The manual’s purpose is to familiarize you with the safe operation, basic function, and features
of this mortiser as well as the set-up, maintenance and identification of its parts and compo-
nents. This manual is not intended as a substitute for formal woodworking instruction, nor to
offer the user instruction in the craft of woodworking. If you are not sure about the safety of
performing a certain operation or procedure, do not proceed until you can confirm, from
knowledgeable and qualified sources, that it is safe to do so.

Once you’ve read through these instructions, keep this manual handy for future reference.

Disclaimer:

The information and specifications in this

manual pertain to the unit as it was supplied from the
factory at the time of printing. Because we are committed
to making constant improvements, General

®

Internatio-

nal reserves the right to make changes to components,
parts or features of this unit as deemed necessary, with-
out prior notice and without obligation to install any
such changes on previously delivered units. Reasonable
care is taken at the factory to ensure that the specifica-
tions and information in this manual corresponds with

that of the unit with which it was supplied. However, spe-
cial orders and “after factory” modifications may render
some or all information in this manual inapplicable to
your machine. Further, as several generations of this mo-
del of mortiser and several versions of this manual may
be in circulation, if you own an earlier or later version of
this unit, this manual may not depict your machine
exactly. If you have any doubts or questions contact
your retailer or our support line with the model and seri-
al number of your unit for clarification.

GENERAL® INTERNATIONAL

8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3

Telephone (514) 326-1161 • Fax (514) 326-5555 • www.general.ca

«
1
2
3
4
...
»

Содержание 75-050T M1























Отзывы:

Нет отзывов

Похожие инструкции для 75-050T M1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды