manualshive.com logo in svg

General Air Products NGP-1000D-M2, Инструкция по установке, эксплуатации и обслуживанию, Страница: 29 / 34

Поделиться
Скачать
General Air Products NGP-1000D-M2 Скачать руководство пользователя страница 29

1-800-345-8207

29

Changing the Batteries

When the batteries need to be changed, the device will indicate this in one of two ways:

1.

The battery icon on the bottom of the display will begin to flash. This icon will continue to flash until the batteries 

are changed. The unit will continue to function normally for approx. 200 hours.

2.

If the device detects a very low battery level, an error code of “E04” will be present on the display, and the unit will

not function until the batteries are changed.

To change the batteries, begin by removing the three screws from the back of the device. A #1 phillips screwdriver is

required to remove these screws. Once the screws are removed, gently separate the two halves of the device.

The batteries can now be replaced from the back half of the case. Be sure to orient the new batteries as indicated in the

embossed polarity on the back case. 

NOTE:

If the batteries are installed incorrectly the batteries will not make contact and

the device will not operate. Carefully, bring the two halves of the case together while positioning the wires so they are not

pinched between the two case halves. The gasket separating the halves will be captured on the back case half.

Reinsert the three screws and tighten until the screws are snug.The device will automatically perform a calibration and

begin displaying % of oxygen.

HELPFUL HINT:

If unit does not function, verify that the screws are tight to allow proper electrical connection.

 

Code

Meaning

Corrective Action

E02 

1RVHQVRUDWWDFKHG

2SHQWKHKDQGKHOGQLWURJHQSXULW\DQDO\]HUDQG
GLVFRQQHFWDQGUHFRQQHFWVHQVRU8QLWVKRXOGSHUIRUPDQ
DXWRFDOLEUDWLRQDQGVKRXOGUHDG,IQRWFRQWDFW
&XVWRPHU6HUYLFHIRUSRVVLEOHVHQVRUUHSODFHPHQW

E02

1RYDOLGFDOLEUDWLRQGDWDDYDLODEOH

0DNHVXUHXQLWKDVUHDFKHGWKHUPDOHTXLOLEULXP3UHVVDQG

KROGWKH&DOLEUDWLRQ%XWWRQIRUWKUHHVHFRQGVWRPDQXDOO\

IRUFHDQHZFDOLEUDWLRQ

E02 or ED4

%DWWHU\EHORZPLQLPXPRSHUDWLQJYROWDJH

5HSODFHEDWWHULHV

CAL Err St: O

2

6HQVRUUHDGLQJQRWVWDEOH

:DLWIRUGLVSOD\HGQLWURJHQUHDGLQJWRVWDELOL]HZKHQ

FDOLEUDWLQJWKHGHYLFHDWR[\JHQ:DLWIRUXQLWWR

UHDFKWKHUPDOHTXLOLEULXP3OHDVHQRWHWKDWWKLVFDQWDNH

XSWRRQHKDOIKRXULIWKHGHYLFHLVVWRUHGLQWHPSHUDWXUHV

RXWVLGHWKHVSHFL¿HGRSHUDWLQJWHPSHUDWXUHUDQJH

CAL Err lo

Sensor voltage too low

3UHVVDQGKROGWKH&DOLEUDWLRQ%XWWRQIRUWKUHHVHFRQGV

WRPDQXDOO\IRUFHDQHZFDOLEUDWLRQ,IXQLWUHSHDWVWKLV

HUURUPRUHWKDQWKUHHWLPHVFRQWDFW&XVWRPHU6HUYLFHIRU

SRVVLEOHVHQVRUUHSODFHPHQW

&$/(UUKL

6HQVRUYROWDJHWRRKLJK

3UHVVDQGKROGWKH&DOLEUDWLRQ%XWWRQIRUWKUHHVHFRQGV

WRPDQXDOO\IRUFHDQHZFDOLEUDWLRQ,IXQLWUHSHDWVWKLV

HUURUPRUHWKDQWKUHHWLPHVFRQWDFW&XVWRPHU6HUYLFHIRU

SRVVLEOHVHQVRUUHSODFHPHQW

CAL Err Bat

%DWWHU\YROWDJHWRRORZWRUHFDOLEUDWH

5HSODFHEDWWHULHV

C

 

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

 

 

Содержание NGP-1000D-M2



































Отзывы:

Нет отзывов