Generac Power Systems RXSW400A3CUL Скачать руководство пользователя страница 6

Introduction and Safety

2

Automatic Transfer Switch Owner’s Manual

General Hazards

(000237)

DANGER

Electrical backfeed. Use only approved switchgear to 
isolate generator from the normal power source.
Failure to do so will result in death, serious injury, 
and equipment damage.

(000195)

DANGER

Electrocution, equipment and property damage. 
Handle transfer switches carefully when installing. 
Never install a damaged transfer switch. Doing so 
could result in death or serious injury, equipment 
and property damage.

(000123)

DANGER

Electrocution. Turn utility supply OFF before 
working on utility connections of the transfer 
switch. Failure to do so will result in death or 
serious injury.

 

(000157)

DANGER

Electrocution. Do not disable or modify the
connection box door safety switch. Doing so
will result in death or serious injury.

Automatic start-up. Disconnect utility power and 
render unit inoperable before working on unit. 
Failure to do so will result in death or serious injury.

(000191)

DANGER

(000119)

Equipment malfunction. Installing a dirty or damaged
transfer switch will cause equipment malfunction and 
will result in death or serious injury. 

DANGER

(000155a)

WARNING

Electric shock. Only a trained and licensed electrician 
should perform wiring and connections to unit. Failure 
to follow proper installation requirements could result in 
death, serious injury, and equipment or property damage.

(000120)

CAUTION

Equipment damage. Verify all conductors are tightened 
to the factory specified torque value. Failure to do so 
could result in damage to the switch base.

 

(000121)

CAUTION

Equipment damage. Perform functional tests in the 
exact order they are presented in the manual. 
Failure to do so could result in equipment damage.

 

(000134a)

CAUTION

Equipment damage. Exceeding rated voltage and 
current will damage the auxiliary contacts. Verify 
that voltage and current are within specification 
before energizing this equipment.

(000237)

DANGER

Electrical backfeed. Use only approved switchgear to 
isolate generator from the normal power source.
Failure to do so will result in death, serious injury, 
and equipment damage.

(000129)

DANGER

Electrocution. High voltage is present at 
transfer switch and terminals. Contact with live 
terminals will result in death or serious injury.

 

(000123)

DANGER

Electrocution. Turn utility supply OFF before 
working on utility connections of the transfer 
switch. Failure to do so will result in death or 
serious injury.

 

(000104)

DANGER

Electrocution. Water contact with a power 
source, if not avoided, will result in death 
or serious injury.

(000188)

DANGER

Electrocution. Do not wear jewelry while 
working on this equipment. Doing so will 
result in death or serious injury.

Содержание RXSW400A3CUL

































Отзывы: