Generac Power Systems 10 KVA, Руководство пользователя

Страница: 21 / 40

Operation
Owner’s Manual for Australian 50 Hz Air-Cooled Generators 17
Figure 3-8. Navigation Menu
Run Log
EXAMPLE:
Inspect Battery 200 RnHr or 12/27/18
and
Next Maintenance 200 RnHr or 12/27/18
Exercise T
ime
Å
HH:MM Day Frequency
Æ
ESC
+ –
++
+
–
ENTER
Current Date/T
ime
Å
2/12/16 12:22
Æ
ESC
ESC
ESC
ESC
ENTER ESC
ENTER
ESC
ENTER
ESC
Maint. Log
Run Hrs
Scheduled
Select Month (1-12)
- 2 +
Run Hours (H)
0.0
Select Date (1-31)
- 13 +
Select Y
ear
(0-99)
- 13 +
Access
Requires Password
Language
Å
English
Æ
Fuel Selection
Å
NG or LP
Æ
Alarm Log
ENTER
ESC
ENTER
ESC
ENTER
ESC
"Battery Maintained"
"Schedule A
Serviced"
"Schedule B Serviced"
"Maintenance Reset"
"Inspect Battery"
"Service Schedule
A"
"Service Schedule B"
W
arning Message(s)
Low Battery
Exercise Set Error
Service Schedule
A
Service Schedule B
Inspect Battery
Stopping...
FIRMW
ARE ERROR-9
Battery Problem
Charger W
arning
Charger Missing
AC
Overload Cooldown
SEEPROM ABUSE
USB W
arning
Download Failure
Overload W
arning
No WIFI
Running Manual
Running-Utility Lost
Running–Remote Start
Running–2 Wire Start
Running–Exercise
Switched Of
f
Stopped -
Auto
Select Min (0-59)
- 0 +
Select Hour (0-23)
- 14 +
Select Min (0-59)
- 0 +
Select Hour (0-23)
- 14 +
Quiet
T
est Mode ?
-
YES or NO +
Select Frequency
- WEEKL
Y
+
- BIWEEKL
Y
+
- MONTHL
Y
+
Language
+ English -
Fuel Selection
+ NG or LP
-
Cold Smart Start? Å
YES or NO
Æ
Cold Smart Start?
-
YES or NO +
Language
+ Francais - + Espanol -
+ Português -
+ ...... -
Battery Condition
“Good”, “Inspect Battery” or
“Check Battery”
Select Day
- W
ednesday +
Generator Activated
Service Unit
Language Update?
Å
YES or NO
Æ
WIFI Enable
Å
YES or NO
Æ
WIFI Enable
–
YES or NO +
<ENT> LOAD LANGUAGE
<ESC> T
O
QUIT
ESC ESC ESC ESC ESC ESC ESC ESC
Current Date/T
ime
10/09/18 07:40
ESC
ESC ENTER
ESC ENTER
ENTER ENTER
T
ime Zone
Country/City
XX - XX/XX/XX XX:XX
XXXXX
XX - XX/XX/XX XX:XX
XXXXX
NOTE 1: Last 50 logs displayed for each (Alarm Log, Run Log, Maint. Log). NOTE 2: Date and time displayed for each occurence. NOTE 3: Error code displayed for each Alarm, Error Code and Alarm
Message
swap every 5 seconds.
Battery
NOTE 1: Last 50 maintenance logs displayed. NOTE 2: Date and time displayed for each occurence.
(If enabled): Refer to the Wi-Fi manual for flow charts relating to Wi-Fi (If not enabled): Displays SETUP
WIFI
Only if Wi-Fi is disabled. Date/T
ime automatically updates if connected to Wi-Fi.
Firmware Update
Å
YES
Æ
Current: V 1.01
USB: V 1.05
Are Y
ou
Sure?
-
Y
es or No +
Update from:
Å
USB or Wi-Fi
Æ
Select
YES, then press ENTER to continue or ESCAPE to cancel update. During
update process, the Blue “Manual” light flashes, then the Green “Auto” light flashes. Sequence then repeats. When update is complete, the unit returns to Install Wizard menu. When the controller powers up, the first screen briefly displays the version number
.
When update is complete, remove USB Drive.
Then follow the Install Wizard Menu.
Firmware Update
<- Insert USB ->
Possible Message(s):
Corrupted File
Invalid File
File Not Found
Unsupported Device*
* Re-try using a higher quality USB drive. File names on the USB cannot have more than 8 characters.
Refer to the Installation Wizard.
Only when WiFi
Activated
SYSTEM
WIFI
DA
TE/TIME
SUB MENUS
HIST
OR
Y
EDIT
MAINT
DEALER
ESC
ENTER
ESC
ENTER
ESC
ENTER ENTER
USB
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
Current: V 1.01
USB: V 1.05
Are Y
ou
Sure?
-
Y
es or No +
ENTER
ENTER
ENTER ENTER
ENTER ENTER
ENTER
ESC
ENTER
ESC
ENTER
Alarm Message(s)
High Engine
T
emp
Low Oil Pressure
Overcrank
Overspeed
RPM Sense Loss
Underspeed
Internal Fault
FIRMW
ARE ERROR-7
WIRING ERROR
Overvoltage
Undervoltage
Overload Remove Load
Low V
olts Remove Load
Stepper Overcurrent
Auxiliary Shutdown
Emergency Stop
Defaults to English. Select desired language by scrolling through list.
ESC
ESC
ESC
ESC
ESC
ESC
0066
67a