background image

 6 

2.  120/240 VAC loads — one load with a maximum total watt-

age requirement equal to the generator’s rated power output, 

and 240V across the generator output terminals; or two sep-

erate loads, each with a maximum total wattage requirement 

equal to half of the generator’s rated power output (in watts), 

and 120V across the generator output terminals. Figure 1.2, 

shows the generator lead wire connections for 120/240 VAC 

loads. Also refer to the "Line Breakers" section for circuit 

breaker ratings.

This procedure should be done by an Authorized Service Dealer or 

other qualified installer.

Figure 1.2 - Connection for 120/240 Volts

T1

RED

T2

WHITE

T3

BLACK

GROUNDED NEUTRAL

STATOR POWER
WINDINGS

CB1

CB2

1.6 SPECIFICATIONS

1.6.1 FUEL 

REQUIREMENTS

This generator is equipped with a gasoline or LP fuel system. 

Specific installations may provide either a separate fuel tank for 

the generator, or the generator may “share” the vehicle engine’s 

fuel tank.

Gasoline Fuel Consumption (gph)

Model

10% Load

50% Load 100% Load

QuietPact 75G

0.51

0.80

1.28

NOTE

Some installations using a “shared” fuel tank may have a gen-

erator fuel pickup tube that is shorter than the vehicle engine’s 

pickup tube.  Such an arrangement causes the generator engine 

to “run out of gas” while adequate fuel for the vehicle remains 

in the tank.

To reduce lead and carbon deposits use high quality UNLEADED 

gasoline with the generator. Leaded REGULAR grade gasoline is an 

acceptable substitute.

NOTE:

Using unleaded gasoline contributes to longer engine valve life 

by reducing lead and carbon deposits.

n

 

 The manufacturer does not recommend using 

any gasoline containing alcohol (such as 

“gasohol”). If using any gasoline containing 

alcohol, it must not contain more than 10 per-

cent ethanol, and it must be removed from the 

generator during storage. Do NOT use any 

gasoline containing methanol. If using gasoline 

with alcohol, inspect more frequently for fuel 

leaks and other abnormalities.

LP Fuel Consumption (lb./hour)

The LP powered range of generators are fitted with a nonadjust-

able, factory set system. These systems are tamper-proof to meet 

1997 California Air Resources Board requirements for engine 

emission.

Model

Idle

50% Load

100% Load

QuietPact 55LP

2.34

3.96

5.07

QuietPact 65LP

2.34

4.20

6.50

QuietPact 75LP

2.34

4.44

8.75

1.6.2  ENGINE OIL REQUIREMENTS

Use only high quality detergent oil rated with American Petroleum 

Institued (API) Classification SF, SG, SH or SJ. The recommended 

oil viscosity weights include the following:

During summer months (40 deg. F and higher), SAE 30 or SAE 

• 

10W-30

During winter months (40 deg. F to -20 deg. F), SAE 5W-30 or 

• 

SAE5W20

DO NOT USE SAE 10W-40

• 
Crankcase and oil filter capacity is approximately 1.8 L or 1.9 U.S. 

quarts. DO NOT use special additives. See sections "Checking the 

Engine Oil Level" and "Changing the Engine Oil and/or Oil Filter" for 

oil level check and filling procedures.

1.6.3 ENGINE 

SPECIFICATIONS

Type of Engine ..................................................................................... GT-760
Cooling Method ...............................................................................Air-cooled
Rated Horsepower ..................................................................27 at 3600 rpm
Displacement .........................................................................................760cc
Compression Ratio ..............................................................................8.6 to 1
Cylinder Block ...................................................  Aluminum w/Cast Iron Sleeve
Type of Governor ......................................................Mechanical, Fixed Speed
Engine Governor Speed

  QUIETPACT 55 .............................................................................. 2200 rpm
  QUIETPACT 65/75 ......................................................................... 2571 rpm
Air Cleaner ................................................. Paper Element w/Foam Precleaner
Starter .................................................................................12-volt DC Electric
Ignition System .............................................. Solid-state w/Flywheel Magneto
Recommended Spark Plug
  Champion .........................................................................................RC14YC
  AC ......................................................................................................... R45S
  Fram Autolite ..............................................................................................65

General Information

Содержание 004703-1

























































Отзывы: