Generac Power Systems 004703-1 Скачать руководство пользователя страница 22

 20 

NOTICE TO INSTALLER

These 

Installation Instructions

 have been published by the manu-

facturer to aid in the installation of the products described in this 

manual. The manufacturer assumes that installation personnel 

are familiar with the procedures for installing such products, or 

similar products manufactured. The manufacturer also assumes 

that personnel have been trained in the recommended installation 

procedures for these products and that such training includes (a) 

use of common hand tools, (b) use of special tools, and (c) use of 

any tools and/or equipment from other suppliers.
The manufacturer cannot possibly know of and advise the rec-

reational vehicle trade of all conceivable methods, procedures or 

techniques by which to perform an installation. Nor can the manu-

facturer anticipate every possible hazard that might result from 

each installation method, procedure or technique. The manufactur-

er has not undertaken any such wide evaluation. Therefore, people 

who use a method, procedure or technique that the manufacturer 

does not specifically recommend must first completely satisfy 

themselves that their safety, the safety of the vehicle's occupants 

and the product's safety is not endangered by the method, proce-

dure or technique selected.
Information, illustrations, specifications, etc., contained in these 

Installation Instructions

 are based on the latest information avail-

able at the time of publication. Every effort has been expended 

to be sure that such data is both accurate and current. However, 

the manufacturer reserves the right to change, alter or otherwise 

improve this product at any time without prior notice.

n

 

 Despite the safe design of this generator, 

operating this equipment imprudently, neglect-

ing its maintenance or being careless can 

cause 

possible injury or death. Permit only responsi-

ble and capable persons to operate or maintain 

this equipment.



 

 Potentially lethal voltages are generated by 

these machines. Ensure all steps are taken to 

render the machine safe before attempting to 

work on the generator.

n

 

 Parts of the generator are rotating and/or hot 

during operation. Exercise care near running 

generators. 

n

 

 

Generator exhaust gases contain DEADLY 

carbon monoxide gas. This dangerous gas, 

if breathed in sufficient concentrations, can 

cause unconsciousness or even death.

GENERAL HAZARDS

For safety reasons, the manufacturer recommends that the 

• 

installation, initial start-up and maintenance of this equipment 

is carried out by an Authorized Service Dealer.

Keep hands, feet, clothing, etc., away from drive belts, fans, 

• 

and other moving or hot parts. Never remove any drive belt or 

fan guard while the unit is operating.

When working on this equipment, remain alert at all times. 

• 

Never work on the equipment when physically or mentally 

fatigued.

Inspect the generator regularly, and contact the nearest 

• 

Authorized Service Dealer immediately for parts needing repair 

or replacement.

Inspect the generator regularly, and contact the nearest 

• 

Authorized Service Dealer immediately for parts needing repair 

or replacement.

Before performing any maintenance on the generator, discon-

• 

nect its battery cables to prevent accidental start up. Disconnect 

the cable from the battery post indicated by a NEGATIVE, NEG 

or (–) first. Reconnect that cable last.

Never use the generator or any of its parts as a step. Stepping 

• 

on the unit can stress and break parts, and may result in dan-

gerous operating conditions from leaking exhaust gases, fuel 

leakage, oil leakage, etc.

ENGINE EXHAUST HAZARDS

Generator engine exhaust contains DEADLY carbon monox-

• 

ide, an odorless, colorless poisonous gas. Breathing carbon 

monoxide can cause: dizziness, throbbing temples, nausea, 

muscular twitching, headache, vomiting, weakness and sleepi-

ness, inability to think clearly, fainting, unconsciousness or 

even death. If you experience any carbon monoxide poisoning 

symptoms, move into fresh air and immediately seek medical 

attention. 

Never operate the generator set with the vehicle inside any 

• 

garage or other enclosed area.

Adequate, unobstructed flow of cooling and ventilating air 

• 

is critical for expelling  toxic carbon monoxide gas and fuel 

vapors from the generator compartment and for proper genera-

tor operation. Without sufficient cooling airflow, deadly carbon 

monoxide gas can accumulate and  the engine/generator may 

quickly overheat, causing serious  damage to the generator. Do 

not operate the genset in any confined space. 

The exhaust system must be installed in accordance with the 

• 

genset installation manual. Do not alter the installation or permit 

even partial blockage of ventilation systems, as this can seri-

ously affect the safe and proper operation of the generator.

n

 

 DANGER: For fire safety, installation of a generator into a recreational vehicle must comply strictly with article 

551, NFPA 70; ANSI C1-1975; AND, ANSI A119.2-1975/NFPA 501C “Standard for Recreational Vehicles” (Part 3, 

“Installation of Electrical Systems”). In addition, installation must comply with the manufacturer’s instructions 

and recommendations.

Safety Rules

Содержание 004703-1

























































Отзывы: