3. Counter clockwise advancement of the
COUNTER-
WEIGHT
(8) will cause the cartridge side of the
TONE
ARM
(7) to be lowered; turning it clockwise will cause the
opposite. Turn the
COUNTERWEIGHT
(8) clockwise or
counter clockwise as needed until the
TONE ARM
(7) is
balanced horizontally. You can easily tell this by watch-
ing for the point where the
TONE ARM
(7) “floats” freely.
4. Place
TONE ARM
(7) on
ARM REST
(11) and lock it
in place with the
ARM CLAMP
(10).
5. With the
TONE ARM
(7) locked on the
ARM REST
(11), hold the
COUNTERWEIGHT
(8) steady with one
hand while rotating the
STYLUS PRESSURE RING
(9)
until the numeral “0” on the ring aligns with the center
line on the
TONE ARM (7)
rear shaft. The horizontal
zero (0) balance should be completed.
6. Re-float the
TONE ARM
(7) to ensure horizontal zero
(0) balance. If zero balance has not been maintained,
repeat counterweight steps 3 - 5.
7. After adjusting the horizontal zero (0) balance, turn
the balanced
COUNTERWEIGHT
(8) counter clockwise
until the cartridge manufacturer’s recommend stylus
pressure appears on the
STYLUS PRESSURE RING
(9)
where it meets the center line of the
TONE ARM
(7) rear
shaft.
ADJUSTING THE ANTI-SKATING CONTROL:
Set the
ANTI-SKATING CONTROL
(12) to the same
value as the stylus pressure.
NOTE: IF YOUR TURNTABLE CAME WITH A CN-25 CARTRIDGE,
IT HAS A RECOMMENED TRACKING FORCE OF 3.0 GRAMS AND
CAN have RANGE FROM 2.5-3.5 GRAMS.
CONNECTIONS:
1. Plug the AC power plug into an appropriate outlet.
2. See
Table A
for proper connection of the output RCA
plugs and ground connector. Make sure that all the plugs
are firmly plugged into the appropriate jacks (phono
inputs).
NOTE: To reduce hum, make sure the ground lug is
firmly connected to the ground screw.
TABLE A:
OPERATING INSTRUCTIONS:
BASIC OPERATION:
1. Place a record on the
SLIPMAT
(4) which sits on the
PLATTER
(2).
2. Select the desired speed by depressing the
33
or
45
SPEED SELECTOR
(16) button.
3. Turn the
POWER
(13) switch to the “
ON
” position, at
which point the
TARGET LIGHT
(14) will light up,
TAR-
GET LIGHTS
(14) are an optional accessory available at
your local retailer.
4. Remove the stylus protector (if applicable to your car-
tridge).
5. Release the
ARM CLAMP
(10) found on the
ARM
REST
(11).
6. Push the
START/STOP
(15) button. The turntable
PLATTER
(2) will start to spin.
7. Carefully position the
TONE ARM
(7) over the desired
position over the record. Lower the
TONE ARM
(7) slow-
ly, while letting go of the
TONE ARM
(7) over the record
where you want to play.
8. When play is over, raise the
TONE ARM
(7), move it
onto the
ARM REST
(11), and secure it with the
ARM
CLAMP
(10).
9.You now have the option of turning off the power by
turning the
POWER
(13) switch to the “
OFF
” position, or
stopping the
PLATTER
(2) by pushing the
START/STOP
(15) button.
INTERRUPTING PLAY:
1. Pushing the
START/STOP
(15) button will cause the
record to stop exactly when the
START/STOP
(15) but-
ton is pressed while playing.
2.Press the
START/STOP
(15) button again to start play-
back with a short
DELAY
effect.
ADJUSTING THE PITCH CONTROL:
1. The
TT-02
is equipped with a
PITCH CONTROL
(17).
When the
PITCH CONTROL
is in the center position,
the speed will be
33
or
45
depending on which
SPEED
SELECTOR
(16) button is pushed.
2. When the
PITCH CONTROL
(17) is positioned off
center, the pitch can vary ±10% depending on the posi-
tion of the
PITCH CONTROL
(17).
SPECIFICATIONS:
TURNTABLE SECTION:
Type.......................................Direct Drive Manual Turntable
Drive Method.......................................................Direct Drive
Motor......................................................................DC Motor
Speed........................................................33 1/3 or 45 RPM
Wow and Flutter............................Less than 0.25% WRMS*
*This rating refers to the turntable assembly and platter only and
excludes effects of records, cartridges or tonearms.
TONEARM SECTION:
Type.............................Statically Balanced Straight Tonearm
Headshell Weight...........................................................5.6 g
GENERAL:
Power Supply....................................115V 60Hz/230V 50Hz
Power Consumption..................................................5 Watts
Dimensions.........................................17.75" x 3.25” x 13.9"
.................................................(450.85 x 82.55 x 353.06mm)
Weight.........................................................12.5 lbs. (5.7 kg)
Specifications are subject to change without notice. The weight
and dimensions shown are approximate.
(5)
Содержание TT-02 MKII
Страница 3: ...TT 0 02 3 ...
