FADER REPLACEMENT
1. UNSCREW THE FADER (B) SCREWS. DO NOT TOUCH INSIDE
SCREWS (C) CAREFULLY REMOVE OLD CROSS FADER AND
UNPLUG CABLE (D)
2. PLUG IN THE NEW CROSS
FADER INTO CABLE (D) AND
PLACE BACK INTO MIXER.
3. SCREW THE CROSS FADER
TO MIXER WITH THE FADER
PLATE SCREWS (B)
4. REPLACE THE FACE OF THE
MIXER AND SCREW THE FOUR
SCREWS BACK IN AND REPLACE THE FADER KNOBS.
MASTER OUTPUT SECTION
The
MASTER OUTPUT SECTION
rotary knobs adjust the volume of the
MAIN
and
ZONE
output and also the
LEFT
and
RIGHT BALANCE
of
those outputs.
MIXER CHANNEL
(NOTE: ALL 5 CHANNELS HAVE THE SAME FEATURES)
CHANNEL INPUT SELECTOR
The
CHANNEL INPUT SELECTOR
switches allow you to choose which
input will be controlled by that channels corresponding
volume
FADER
.
For example on
CHANNEL (1)
the
INPUT SELECTOR
allows you to
choose between
LINE 1
in or
MIC 2
in, and on
CHANNEL (2)
The
INPUT
SELECTOR
allows you to choose between
PHONO 1/LINE 2
and
LINE 3
,
and also on
CHANNEL (3)
the
INPUT SELECTOR SWITCH
will let you
choose between
PHONO 2/LINE 4
and
LINE 5
then on
CHANNEL (4)
you
may choose between
LINE 6
and
MIC 3
and on
CHANNEL (5)
you can
choose between
LINE 7
and
LINE 8
. (see
CONVERTIBLE LINE INPUT
)
for
PHONO 1/ LINE 2
and
PHONO 2/ LINE 4
switching.
CHANNEL ROTARY GAIN
The
CHANNEL ROTARY GAIN
allows you to boost the signal of each indi-
vidual channel depending on how low or high its input level is
CHANNEL VOLUME FADER
After you have chosen which input you will use with the
INPUT SELEC-
TOR
the corresponding
CHANNEL FADER
will allow you to adjust the vol-
ume for that particular
CHANNEL
.
CHANNEL CUE BUTTONS
The
CHANNEL CUE BUTTONS
allow you to individually choose which
channel you wish to monitor in your headphones, you can monitor one at a
time or any combination of the five.
3 BAND EQUALIZER
The
3 BAND EQUALIZER
adjust the tone of each
CHANNE
L by giving
you a choice
3
frequencies (
BANDS
) to adjust , from
LOW,
MIDRANGE (MID)
and
HIGH’s
,you can use the adjustment knobs to
higher or lower the 3 seprate frequencies till the sound of the music pro-
gram is approppriate for your listening enviroment.
CONTROLS CONTINUED
10
14
11
15
19
“Ipod Friendly” Cable:
To connect your Ipod or other
Digital Media Player, use the included Ipod cable.
Connect the 1/8” end of the cable to the headphone
or line out jack of your player, and connect the RCA to
the line input of your mixer.
SPECIFICATIONS
INPUTS:
Phono.....................................................................................3mV,47 KOhm
Line..................................................................................150 mV, 27 KOhm
MIC......................................................................1.5 mV, 1 KOhm Balanced
OUTPUTS:
Max...................................................................................20V Peak-to Peak
Rec.....................................................................................225 mV, 5 KOhm
GENERAL:
Frequency Response.................................................20Hz - 20KHz +/- 2db
Distortion..........................................................................................< 0.02%
S/N Ratio...........................................................................Better than 85 dB
Headphone impedance..................................................................16 Ohm
Power Source (external)......................................................AC 15V, 500mA
Unit Demensions.....................................................................19” x 3.3” x 7”
..........................................................................(482.6 x 83.82 x 177.8 mm)
Weight................................................................................6.35 lbs (2.88 kg)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION FOR IMPROVEMENT
MM-3000
CROSS FADER
The
CROSS FADER
allows you to mix evenly from one source to another.
On the
MM-3000
The
CROSS FADER
is assignable between all (5) chan-
nels. The
CROSS FADER
on the
MM-3000
is also removable and if the
need arises can be replaced.The
RG-45
(
RAILGLIDE
™
)
DUAL-RAIL
CROSS FADER
, which has internal dual stainless steel rails that allow the
slider to ride smoothly and accurately from end to end can be purchased
from your local
GEMINI
dealer.
CROSSFADER ASSIGN SWITCH
The
CROSSFADER ASSIGN SWITCH
allows you to assign any of the
mixer
CHANNELS
to the crossfader. The
CROSSFADER
will then mix
smoothly between the two assigned channels. Any channel not assiged to
the
CROSSFADER
will work normally.
NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE
FADER BACK AND FORTH. PRESSING DOWN ON THE CONTROLS
CAN BEND CONTACTS AND CAUSE A LOSS OF SOUND
.
12
22
13
