(6)
CUE-B/EXIT:
After a
CUE POINT
is memorized, pressing the
CUE-B/EXIT
(18)
button in
PLAY
mode, repeats the section between the
CUE POINT
and the point where the
CUE-B/EXIT (18)
button
was pressed. Press
the
CUE-B/EXIT (18)
button again or pause play to exit the repeating play.
RELOOP/STUTTER: RELOOP/STUTTER (19)
is used for repeated play
(stutter) from the cue point, repeating a previously set
LOOP
. The
reloop function automatically returns the music to the
CUE POINT
and
will play the
LOOP
until it is released with the
CUE-B/EXIT BUTTON
(19)
.
CD starts instant play from the previously set
CUE POINTS
.
MEMO (CUE 1-3):
The
CFX-40
allows you to set up to
3
different
CUE
POINTS
using the
CUE 1-3
(20)
buttons. To set each individual
CUE
POINT
, press the
MEMO (20)
button and then a
CUE 1-5
button. You
can keep setting
CUE POINTS
up to
3
. As your music is playing, if you
would like it to jump to one of your set
CUE POINTS
, simply press that
individual
CUE
button and the music will jump to that point.
JOG WHEEL:
Use the
JOG WHEEL (21)
to make fine adjustments in
PAUSE
mode when setting a
CUE POINT
. Use the
JOG WHEEL (21)
to bend the
PITCH
for precise synchronization in
PLAY
mode. In
VINYL
mode use the
wheel to
SCRATCH
the music. If you move the wheel back and forth the
music will stop and play like a vinyl turntable. When the
JOG WHEEL (21)
stops moving the music will continue. If you are using any
EFFECTS
in
CD
MODE
the
JOG WHEEL (21)
will adjust the parameter of an
EFFECT
.
JOG MODE:
Press
JOG MODE (22)
to change from
CD
to
VINYL
mode.
When in
VINYL
mode
EFFECTS
can be heard while you
SCRATCH
.
EFFECTS (FILTER, ZOOM, TRANS, ECHO):
Press any one of four
EFFECTS (23): FILTER, ZOOM, TRANS,
or
ECHO
buttons,
to use
that
EFFECT
, and then turn the
JOG WHEEL (21)
to adjust the
EFFECT
parameters of the selected
EFFECT
. Use the
EFFECTS (23)
buttons to
turn the
EFFECTS ON
and
OFF
.
MASTER TEMPO BUTTON:
The
MASTER TEMPO BUTTON (24)
control
locks in the music’s pitch even when the tempo changes. You can vary
the beat with no change in vocal or instrument tone.
PITCH BEND BUTTONS:
Pushing the
PITCH BEND
BUTTONS
(25)
will
automatically raise the pitch up to
+4%
or lower the pitch down to
-4%
from the existing pitch setting. Releasing the buttons will return the pitch
to the original pitch setting. You can use this function to match the pitch
bend when mixing from one song to another.
PITCH:
Pushing the
PITCH BUTTON (26)
activates the
PITCH CONTROL
SLIDE (28)
. The pitch of the CD will change according to the position of
the
PITCH CONTROL SLIDE (28)
.
PITCH SELECT (4%, 12%, 24%, & 100%):
Use the
PITCH SELECT (34)
button to assign the percentage of
PITCH
the
PITCH CONTROL SLIDE
(28)
will have. The
4%
button will assign
+/-4%
to the pitch control slide.
The
12%
button will assign
+/-12%
to the pitch control slide. The
24%
button will assign
+/-24%
to the pitch control slide. Press and hold
PITCH SELECT (34)
for
100% PITCH
. The
PITCH (26)
button must be
ON
for the
PITCH SELECT (27) 4%, 12%
and
24%
button
to work.
PITCH CONTROL SLIDE:
Moving the
PITCH CONTROL SLIDE (28)
up
or down will lower or raise the pitch percentage.
ROBO START:
Press the
ROBO START BUTTON
(29)
to activate
ROBO
START
function
(the button will blink). Use
ROBO START
in
SINGLE-
AUTO CUE MODE
to alternate play between the two sides of the CD
player (one track from one side, then one track from the other side).
See the
ROBO START
instructions section for further instructions.
PGM (PROGRAM):
Use the
PGM (30)
section for
DIRECT SELECT
or
to create a
TRACK PROGRAM
. Please refer to the
PGM
section for
detailed instructions.
OPERATIONS:
1. Make sure that the
VOLTAGE SELECTOR (1)
switch,
found on the rear
panel, is set for the proper voltage. Plug the unit in and press the
POWER (6)
button. The unit will turn on. Pushing the
POWER
(6)
button
a second time will turn the unit off.
2. Press the
STOP (8)
button, place a CD in the
DISC TRAY (7)
and press
the
STOP (8)
button again. The tray will close into the unit.
3. Push the
TRACK (13)
buttons to select the track you want to play.
4. Press the
PLAY/PAUSE (11)
buttons and the unit will instantly play.
EFFECTS:
Press any one of the four
EFFECTS (23): (FILTER, ZOOM, TRANS,
and
ECHO)
buttons
to use an effect. The
FILTER
effect allows you to
change the cutoff frequency of the playback sound. This allows the DJ
to extract and play back specific parts from the playback sound. The
ZOOM
effect changes the delay time by mixing a short delay with the
playback sound. This function allows you to produce the sound of a
jet
engine or flanger effect using a single CD player.
TRANS
cuts off the
audio signal in cycles causing a stutter effect, the length of the
incoming sound will decrease as the parameter increases.
ECHO
repeats the music and will create a reverb with higher parameters. The
JOG WHEEL (21)
controls the
PARAMETERS
of the
EFFECTS
. Turning the
JOG WHEEL (21)
to the
RIGHT
and
LEFT
will
INCREASE
and
DECREASE
the
PARAMETERS
of an
EFFECT
. To turn the
EFFECT OFF
,
press the
EFFECT
button that is
ON
again, to turn it
OFF
.
CUES:
FLY CUE:
To use
FLY CUE (17)
to set a
FLY CUE POINT
and
SEAMLESS LOOP
follow these instructions:
1. While a track is in
PLAY
mode, press
FLY CUE (17)
at the point where
you want the
CUE POINT
to be, (
FLY CUE (17)
will flash green and
CUE/PREVIEW (11)
will flash blue) as the CD plays. Now that a
CUE
POINT
is memorized, press the
CUE/PREVIEW
(11)
button to return to
the
FLY CUE POINT
at any time. Push the
PLAY/PAUSE (11)
button,
and the unit will instantly play from the
CUE POINT
selected. Pressing
RELOOP STUTTER (19)
will also start
PLAY
from the
CUE POINT
.
2. To create a
SEAMLESS LOOP
press
FLY CUE (17)
to memorize a
CUE
POINT
. Using the previously selected
CUE POINT
, press the
CUE-B/
EXIT (18)
button to activate an
EXIT POINT
and start the
LOOP
, (the
FLY CUE (17)
and
CUE-B/EXIT (18)
buttons will flash green together).
Press
CUE-B/EXIT (18)
to
EXIT
the
LOOP
at any time, and press
RELOOP STUTTER (19)
to activate the
LOOP
.
MEMO CUE:
Another easy way to set
CUE POINTS
is the
MEMO (CUE-1-3) (23)
.
You can store up to
3 CUE POINTS
in memory from any track within a
CD. Just press
MEMO (20)
then select any
1
of the
3 CUE POINTS
(CUE 1-3)
to set a
CUE POINT
. Once you set a
MEMO CUE POINT
you
can return to that
CUE
by pressing it again. If the CD is
PLAYING
it will
play from the
CUE POINT
and if the CD is
PAUSED
the
CUE POINT
will
be
PAUSED
as well.
MEMO POINTS
are locked in memory until that CD
is ejected from the CD player.
NOTE: THE MEMO CUES CAN ALSO BE SET IN PAUSE MODE USING THE JOG WHEEL FOR
PRECISE CUE POINTS.
PLAY CUE:
1. To memorize the spot at which you want play to start, select the proper
track, and then push the
PLAY/PAUSE (11)
button so the unit goes
into the
PLAY
mode (
PLAY/PAUSE (11)
LED
will glow green). Listen to
the CD and when the CD gets to the approximate spot, push
PLAY/
PAUSE (12)
so the unit goes into
PAUSE
mode (
PLAY/PAUSE (11)
LED
will blink green). Move the
JOG WHEEL (21)
to the precise spot you
want play to begin and push the
PLAY/PAUSE
(11)
button to memorize
the
CUE POINT
. Press the
CUE
BUTTON
(12)
to return to the memorized
CUE POINT
. Push the
PLAY/PAUSE BUTTON
(11)
, and the unit will
instantly play from the spot selected.
2. To fine tune a
CUE POINT
, pause play at the memorized
CUE POINT
(the
CUE/PREVIEW
(12) LED
will glow and the
PLAY/PAUSE (11)
LED
will blink), then use the
JOG WHEEL (21)
to scan frame by frame (1/
75th of a second) to where you want play to begin (the
CUE LED
will
blink while you scan). Press
PLAY/PAUSE (11)
to save the new cue point.
NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT (TO HELP YOU FIND
THE BEAT). THE STUTTERING EFFECT WILL END WHEN YOU PRESS THE PLAY/PAUSE (11)
TO SAVE THE CUE POINT.
