(3)
VOLTAGE SELECTOR:
To set the proper voltage, adjust the
VOLTAGE SELECTOR (1)
switch to
115
or
230
volts.
POWER JACK (AC IN):
Connect the power plug into the
POWER JACK (2)
for power.
REMOTE CONTROL:
Use the included
CABLE & REMOTE CONTROL (3)
jacks to connect the
REMOTE CONTROL
to the
MAIN UNIT
.
LINE OUTPUT JACKS:
LINE OUTPUT JACKS (4)
provide stereo sound via included
RCA
cables to your mixer or receiver.
NOTE: MAKE SURE CABLES ARE PLUGGED IN TIGHT FOR OPTIMAL SOUND.
DIGITAL OUTPUT (COAXIAL):
Use the
COAXIAL (5)
jack to connect to any type of device that accepts digital signals.
POWER:
Press the
POWER (6)
button to turn on the CD player.
NOTE: MAKE SURE VOLTAGE SELECTOR SWITCH (1) IS SET BEFORE USE.
DISC TRAY:
Put a CD in the
DISC TRAY (7)
after pressing
STOP (8)
; trays
hold both
12 cm
and
8 cm
CDs.
STOP:
Tap the
STOP (8)
button once to
STOP
the CD, twice to open the
DISC TRAY (7)
, and a third time to close the tray.
NOTE: THE STOP (8) BUTTON ONLY FUNCTIONS AS STOP AND EJECT ON THE REMOTE CONTROL.
DISPLAY:
The
DISPLAY (9)
shows the various functions for the CD Player. See
FUNCTION DESCRIPTIONS
for details.
PLAYBACK DISPLAY BAR:
The
PLAYBACK DISPLAY BAR (10)
shows the
TIME ELAPSED
and
TIME REMAINING.
PLAY/PAUSE:
Press
PLAY/PAUSE (11)
button to activate
PLAY
or
PAUSE
mode. See
CUE
or
ROBO START INSTRUCTIONS
for details.
CUE/PREVIEW:
Tap
CUE/PREVIEW (12)
to come back to a set
CUE
or press and hold to
PREVIEW
from a
CUE POINT
, refer to
CUE INSTRUCTIONS.
TRACK:
Press the
TRACK (13)
buttons to select which
TRACK
to play.
SEARCH:
Use the
SEARCH (14)
buttons to scan forward and reverse directions on a
TRACK.
TIME:
Tap the
TIME (15)
button to switch the
TIME
preference in three modes:
ELAPSED, REMAIN, TOTAL REMAIN.
SINGLE:
Tap
SINGLE (16)
for
SINGLE AUTO CUE
,
CONTINUOUS
, and
NORMAL
modes.
FLY CUE:
FLY CUE (17)
sets a
SEAMLESS LOOP CUE POINT
on the fly.
CUE-B/EXIT:
Press
CUE-B/EXIT (18)
in
PLAY
mode, after a
CUE POINT
is memorized to start a
LOOP
, press again to exit
LOOP.
RELOOP STUTTER:
To play from a saved
CUE POINT
or a
LOOP
, press
RELOOP STUTTER (19)
to play the
LOOP
or the
CUE
again
.
MEMO (CUE 1-3):
Press
MEMO (20)
,
then select a
CUE POINT
from
CUE1-3 (20)
followed by the same number again to set a
CUE POINT
.
Press
CUE1-3 (20)
to play from the set
CUE POINT
.
JOG WHEEL:
The
JOG WHEEL (21)
has various functions such as
PITCH BEND
,
CUEING
,
VINYL MODE
,
and
EFFECT PARAMETERS
.
JOG MODE:
Press to change the
JOG MODE (22)
of the
JOG WHEEL (21)
from
CD
to
VINYL
mode.
EFFECT:
Press an
EFFECT
button:
FILTER
,
ZOOM
,
TRANS
, or
ECHO (23)
, to activate an
EFFECT
. Tap the
EFFECTS (23)
button to release.
MASTER TEMPO:
Pressing
MASTER TEMPO (24)
locks the
PITCH
of a track with no change in vocal or instrument tone.
PITCH BEND:
Buttons for
PITCH BEND (25)
, lower or raise the pitch percentage
(-
or
+ 4%)
when pressed.
PITCH:
The
PITCH (26)
button activates the
PITCH CONTROL SLIDE (27)
.
PITCH SELECT (4%, 12%
,
24%, & 100%):
Use the
PITCH SELECT (27)
button to change the
PITCH
settings from
4%
,
12%
,
&
24%
.
Press and hold for
100% PITCH
.
PITCH CONTROL SLIDE:
Moving the
PITCH CONTROL SLIDE (28)
up or down will lower or raise the pitch percentage.
ROBO START:
Using
ROBO START (29)
enables you to alternate play between two CDs using both sides.
PGM (PROGRAM):
First choose a side by selecting
A
or
B (30)
. For track programming press
PGM (30)
then enter a track number followed by
PGM (30)
and so-forth. For direct selection press a
TRACK NUMBER
followed by
SET (30)
then
PLAY/PAUSE (11)
to jump to that track.
NOTE: FOR FURTHER EXPLANATION PLEASE SEE PGM SECTION.
QUICK ST
QUICK ST
QUICK ST
QUICK ST
QUICK STAR
AR
AR
AR
ART GUIDE
T GUIDE
T GUIDE
T GUIDE
T GUIDE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
