TRACK SKIP
:
The
TRACK SKIP(15)
buttons let you scan forward
or in reverse through the CD to select a track to play. Holding the
button will increase the speed of scanning.
SEARCH
:
The
SEARCH
(16)
buttons are used to move forward
or reverse while in play or pause mode,
SEARCH
(16)
can also be
used to find a
CUE POINT
. Hold down either button for ultra
fast searching.
SEARCH JOG WHEEL
:
The
SEARCH JOG WHEEL(17)
has two
functions. Use the
SEARCH JOG WHEEL(17)
to fast forward or
rewind to a precise location for
CUE
in
PAUSE (STUTTER)
mode. Use
the
SEARCH JOG WHEEL(17)
to bend the pitch for precise
synchronization when beat matching in
PLAY
mode, clockwise for fast
forward to speed up, or counter clock wise for slow motion to speed
down play according to the
PITCH(25)
selected (see
PITCH
below)
.
SINGLE AUTO CUE/CONTINUOUS:
Pressing
SINGLE(18)
activates the
SINGLE-AUTO CUE
function.
SINGLE(18)
allows you to begin and
end play on only one selected track.
AUTO CUE
places the selected
track in pause at the exact moment when the music starts with no
“dead” space in between songs. Once this track has completed playing
the
SINGLE-AUTO CUE
function will pause the CD at the exact
moment when the next track begins playing. Pressing
SINGLE(18)
a
second time will activate the
CONTINUOUS
function.
CONTINUOU
S
allows the CD to play out each track on the CD respectively and will
start over at the beginning, repeating the CD again, until the
SINGLE(18)
function is pressed a third time. This will return these
playback functions to normal mode and play the CD once through as
recorded.
TIME
:
The
TIME(19)
button switches the time display between the three
modes.
ELAPSED
refers to the time past on a track
, REMAINING
refers to the time remaining on the track
,
and
TOTAL REMAINING
refers to the time remaining on the CD
.
Time is measured in
minutes, seconds and frames.
LOOP-IN:
LOOP-IN (20)
activates a
CUE POINT
for the beginning of a
SEAMLESS LOOP
. When pressed the
GREEN LED
on the button will
blink during saving and stays lit during playback or storage. These
CUE POINTS
can be selected at any point in the track to begin a loop.
LOOP-OUT:
Use
LOOP-OUT (21)
to set an
EXIT POINT
for a
SEAMLESS LOOP
after using
LOOP-IN (20)
to start the loop. The
GREEN LED
for
LOOP-OUT (21)
flashes and the
CUE-B
notification
will be visible in the upper right hand corner of the
DISPLAY (10)
for
that side. Press
LOOP-OUT (21)
again to exit the
SEAMLESS LOOP
.
RE-LOOP:
RE-LOOP (22)
will reactivate a
SEAMLESS LOOP
during
playback and starts playback from the
LOOP-IN (20) CUE POINT
similar to the
BOP (14)
button when a loop is not in memory.
NOTE: YOU CAN ONLY USE YOUR LOOP WITH THE CURRENT CD. ONCE YOU OPEN THE
TRAY TO CHANGE CDS, YOUR LOOPS WILL BE AUTOMATICALLY DELETED.
PITCH
:
Pushing a
PITCH(24)
button,
4%, 8%
, or
16%
, activates the
PITCH(24)
section of the unit. The
PITCH
is located at the bottom right
LCD DISPLAY(10)
. To accurately adjust the pitch, change the position
of the
PITCH CONTROL SLIDE(25)
. Pushing
4%
and
16% PITCH(24)
buttons simultaneously will turn off the
PITCH
.
PITCH BEND
:
Pushing the
PITCH BEND (23)
buttons will automati
cally raise the pitch up to
+4%
or lower the pitch down to
-4%
from the
existing setting. Releasing the buttons returns pitch to the original
setting. Use this function to match the pitch bend when mixing from one
song to another. Or use
SEARCH JOG WHEEL (17)
see above.
4%, 8%, and 16%
(24):
Use the
4%, 8%,
and
16%
buttons to assign the
percent the pitch control slide will have.
When a pitch setting is
selected, the
GREEN LED
will light for that button.
The
4%
button will
assign
+/- 4%
to the
PITCH CONTROL SLIDE(25)
. The
8%
button will
assign
+/-8%
to the
PITCH CONTROL SLIDE(25)
. The
16%
button will
assign
+/-16%
to the
PITCH CONTROL SLIDE(25)
. The
PITCH
must
be
ON
for the
4%, 8%,
and
16%
to work.
PITCH CONTROL SLIDE:
Moving the
PITCH CONTROL SLIDE (25)
up
or down will lower or raise the pitch percentage depending on which
pitch level is selected.
ROBO START:
Press the
ROBO START (26)
button to activate the
ROBO
START
function. Use
ROBO START(26)
with the
SINGLE (18)
buttons
different modes to initiate alternate play between the two sides of the
CD player, using one track from each side. The
GREEN LED
will light
up when this function is active. See the
ROBO START(26)
instructions section for detailed instructions.
DIGITAL OUTPUT JACK
(5):
Connecting any type of
DAT, MD, HARD
DRIVE,
or other such items which accept digital signals to the BNC
output connector on the rear panel of your
CDX-04
CD player allows
you to record a digital signal from CD.
OPERATING INSTRUCTIONS:
1. Make sure that the
VOLTAGE SELECTOR(1)
found on the rear panel,
is set for the proper voltage. Plug the unit in and press
POWER(6)
.
The unit is
ON
. Pushing Power a second time turns the unit
OFF
.
2. Press
and place a
CD
on the opened
DISC TRAY(7)
. Press
EJECT(8)
again. The tray will close and the
CD
will load.
3. Push
TRACK SKIP(15)
to select the track you wish to play.
4. Press
PLAY/PAUSE(12)
and the unit will instantly play.
CUE INSTRUCTIONS:
1. To preprogram a
CUE POINT
(the spot on a
CD
at which you want to
start) select the proper track and push
PLAY/PAUSE(12)
so the unit
enters play mode as the
PLAY/PAUSE LED(12)
glows green. When
the
CD
reaches the approximate musical spot you wish to make your
cue, push
PLAY/PAUSE
so the unit enters the
PAUSE (STUTTER)
mode and the
PLAY/PAUSE LED(12)
blinks. Move the
SEARCH JOG
WHEEL(17)
or
SEARCH(16)
buttons forward or in reverse until the
precise spot at which you want
CD
play to begin is located. Push
PLAY/PAUSE(12)
. The
CUE(13)
point is now programmed and the
CUE LED(13)
will glow
BLUE
. Press
CUE(13)
to return to this pre-
programmed cue point at any time. Push
PLAY/PAUSE(12)
and the
unit will instantly play from the pre-selected spot.
2. To fine tune your pre-programmed point, push
PLAY/PAUSE(12)
so the
unit enters the
PLAY
mode. Push the
CUE(13)
button and the
CD
will
return to the
CUE
point you programmed in step #1, hold down
CUE(13)
begin a
PREVIEW
from that point. If you decide to keep this
CUE
point, leave the unit alone until you are ready to mix in from the
CUE
point.
3. If the
CUE POINT
spot is not exactly where you want it to be
press
CUE(13)
and repeat steps
1
&
2.
NOTE: DURING FINE TUNING USE STUTTER MODE IS TO HELP YOU FIND THE BEAT.
STUTTER MODE WILL END WHEN YOU PRESS PLAY/PAUSE (12) TO SAVE THE CUE
POINT.
SEAMLESS LOOPS:
1. To start a
SEAMLESS LOOP
press a
LOOP-IN(20)
button for both
loops on top or bottom on either side during playback. When you
press
LOOP-IN(20),
the
GREEN LED
will flash and stay solid after a
CUE-POINT
is selected.
CUE POINTS
for
SEAMLESS LOOPS
can be
selected on the
FLY
, with any of the
LOOP-IN(20)
buttons.
2. To select the
EXIT POINT
use
LOOP-OUT(21)
to initiate the
SEAMLESS LOOP
. The
GREEN LEDs
for
LOOP-IN(20)
,
LOOP-
OUT(21)
,
RELOOP(22)
& the
CUE-B
notification in the
DISPLAY
will
blink. Press
LOOP-OUT(21)
again to exit the
SEAMLESS LOOP
,
CUE-B
will remain solid.
3. Use
RE-LOOP(22)
to
reactivate a
SEAMLESS LOOP
during playback
or start playback from the
LOOP-IN(20) CUE POINT
just like the
BOP(14)
feature when a
SEAMLESS LOOP
is not in memory.
(5)
