GEA T.VIS M-15 Скачать руководство пользователя страница 76

Страница: 76 / 130

Mounting the Control Top to Different Valves

Mounting to VESTA Valve H_A/M

Operating Instructions · Control Top T.VIS

M-15

Edition 2017-10-16

Mounting to VESTA Valve H_A/M

Requirement:



Pay attention not to kink the air hoses when mounting the control top.

IMPORTANT NOTE

The permanent magnet on the switch bar is fragile.

Damage to the permanent magnet.



Protect the permanent magnet against impact stress.

IMPORTANT NOTE

Magnetic fields resulting from the permanent magnet on the switch bar.

Magnetic fields can delete data carriers and affect or destroy electronic or mechanical
components.



Protect the components against the magnetic fields from the switch bar.

Carry out the following steps:

Complete the T.VIS mounting base (198) with O-rings (29, 101) and a plain bearing
(202).

Screw the mounting base (198) into the actuator (A4) and tighten using a face
spanner.

Screw the switch bar (1) with ring (99) into the piston rod (A4.1) and tighten using an
open end spanner, tightening torque 2 Nm.

Fit the control top (B) over the switch bar (1) and on the actuator.

Содержание T.VIS M-15



































































































































Результаты поиска

Содержание T.VIS M-15

Отзывы:

Бренды по названию

Популярные бренды

GEA T.VIS M-15, Руководство по эксплуатации

Результаты поиска

Содержание T.VIS M-15

Отзывы:

Бренды по названию

Популярные бренды