GEA Hilge HYGIA K Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 36

background image

26

Hilge GmbH & Co. KG | BA.H2A.KYY.001.01.17.GB

Operating manual

GEA Hilge HYGIA K

Maintenance/servicing

15.Push the assembly sleeve onto shaft 0211.00 to enable the

clamp connection to be positioned.
The assembly sleeve is supplied with the pump.

MF-822

Fig. 30: Assembly sleeve

16.Screw on impeller nut 0922.00 without the O-ring and

tighten. The correct length of the shaft is now set.

MF-820

Fig. 31: Pump shaft

17.Tighten hexagon screws 0901.49 of the clamp connection

crosswise.
Torque: First tighten at 5 Nm and then at 8 Nm.

MF-1049

Fig. 32: Clamp connection

18.Remove impeller nut 0922.00

and the assembly sleeve.

19.Check the radial run-out of pump shaft 0211.00. Max. per-

missible deviation: 0.05 mm.
In the event of greater deviations: Remove the clamp con-
nection and re-install.

MF-1050

Fig. 33: Measuring the pump shaft

Only in the case of a replacement lantern:
20.Thoroughly clean the surface of the lantern 0340.00 and

stick the name plate 0970.00 on.

«
...
24
25
26
27
28
...
»

Содержание Hilge HYGIA K





































Отзывы:

Нет отзывов

Похожие инструкции для Hilge HYGIA K

Бренд: Jacuzzi Страницы: 8

Бренд: Jecod Страницы: 3

Бренд: YAMADA Страницы: 14

Бренд: A.O. Smith Страницы: 2

Residential Gas Water Heaters

Бренд: A.O. Smith Страницы: 84

Бренд: EINHELL Страницы: 44

SUPER T T6A60S-4LE2X FT4 Series

Бренд: GORMAN-RUPP PUMPS Страницы: 48

PROTÉGÉ RPAGP

Бренд: Raypak Страницы: 3

CTC EcoPart 400

Бренд: Regulus Страницы: 26

sanitary T Series

Бренд: TapFlo Страницы: 24

Бренд: Lumax Страницы: 28

EKHWS 150D3V3 Series

Бренд: Daikin Страницы: 20

CENTRO-MATIC 85430

Бренд: Lincoln Страницы: 14

Бренд: Wilo Страницы: 32

Бренд: American Standard Страницы: 2

Бренд: Calorex Страницы: 28

Бренд: Dirty Hand Tools Страницы: 20

Бренд: Bryant Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды