GE TruTrak+ 3900 Скачать руководство пользователя

Страница: 50 / 107

3900/3900P User’s Manual

3-2

Message

Possible cause(s)

Recommended action(s)

Appears between the alarm

limit settings (and beside

the first menu option on
Japanese menu screens).

The all mute feature is activated.

No action required. (Press the
alarm silence button once to
deactivate.)

Appears in message area

on waveform screen.

The alarm or pulse tone volume is
being adjusted.

No action required. To adjust
audio volume, see

Front panel

chapter 1.

Appear on status screen

during power-on sequence

and on right side of LCD

during battery operation.

Indicates a fully charged battery.

Indicates a low-charged battery.

No action required.

To recharge, plug the unit into AC
mains power.

Appears on status screen

during power-on sequence.

Indicates battery failure, or a
depleted or missing battery.

To recharge, plug the unit into AC
mains power. If the condition
persists, the unit requires service.

AMBIENT LIGHT

Excessive ambient light.

Relocate the sensor to a site more
shielded from light or reduce the
amount of light shining on the
sensor.

BUTTON STUCK

Appears if something is pressing
against the buttons on the
monitor.

Appears when the last button you
pressed has not released properly
or has been pressed for more than
30 seconds.

Make sure nothing is pressing
against the front of the unit.

Press that button again or turn the
power off and then on. If the
condition persists, the unit
requires service.

CHECK SENSOR SITE

Appears when SpO

readings

may be invalid due to motion, an
unacceptable sensor site, poor
placement, low perfusion, or
because the sensor is off the
patient.

For all causes, reposition or
relocate the sensor, and/or
increase perfusion (see the sensor
user instructions).

CONNECT UNIT TO LINE POWER

The battery needs immediate
recharging.

Plug the oximeter into the AC
power supply; otherwise the unit
will turn itself off in 10 seconds.

Содержание TruTrak+ 3900












































































































Результаты поиска

Содержание TruTrak+ 3900

Отзывы:

Похожие инструкции для TruTrak+ 3900

Бренды по названию

Популярные бренды

GE TruTrak+ 3900, Руководство пользователя

Результаты поиска

Содержание TruTrak+ 3900

Отзывы:

Похожие инструкции для TruTrak+ 3900

Бренды по названию

Популярные бренды