GE TMO2D Скачать руководство пользователя страница 65

Страница: 65 / 102

TMO2D Digital Display User’s Manual

Chapter 5. Advanced Programming

5.5 Select Tracking?

If you use a background gas, the Select Tracking? option enables the TMO2D to use the last data point as the starting
point for the calculation.

5.6 Select Tertiary?

When activated, the

Select Tertiary?

option enables the TMO2D to calculate the ratio of background gases in the

process.

Note:

This option applies only for a TMO2 oxygen transmitter.

5.7 Response Parameters?

If the system response on the TMO2D is set to FAST (see

Select Response?

on page 38), you can program the settings

for the Fast Response algorithm.

IMPORTANT:

If you wish to use Fast Response, consult the factory.

The first setting, Tau (up), is the tau value for calculations while the measured gas concentration is increasing.
Increasing the Tau (up) reading increases the transmitter’s response speed.

Note:

Be careful when setting the Tau (up) or (down) values. Values that are too high may cause the TMO2D
readings to overshoot the actual end point.

FACTORY SETUP MENU
Select Tracking?

Press [YES] to select tracking.

Turn Tracking:
[ON] off

Use the [NO] or arrow keys to scroll to the desired option. Press [YES] to confirm
the entry.

FACTORY SETUP MENU
Select Tracking?

Press [NO] to proceed to the Select Tertiary? option.

FACTORY SETUP MENU
Select Tertiary?

Press [YES] to select tertiary calculation.

Turn Tertiary:
[ON] off

Use the [NO] or arrow keys to scroll to the desired option. Press [YES] to confirm
the entry.

FACTORY SETUP MENU
Select Tertiary?

Press [NO] to proceed to the Response Parameters? option.

FACTORY SETUP MENU
Response Parameters?

Press [YES] to set the parameters for the Fast Response algorithm.

FACTORY SETUP MENU
Tau (up) [XX.XX]:

Use the numeric keys to enter the desired value. Press [YES] to enter the number,
and [YES] again to confirm the entry.

Содержание TMO2D







































































































Результаты поиска

Содержание TMO2D

Отзывы:

Похожие инструкции для TMO2D

Бренды по названию

Популярные бренды

GE TMO2D, Руководство пользователя

Результаты поиска

Содержание TMO2D

Отзывы:

Похожие инструкции для TMO2D

Бренды по названию

Популярные бренды