GE SX Series Скачать руководство пользователя

Страница: 66 / 69

RS-232 MEMORY MAP TABLES

SX TRANSISTOR CONTROL

Page

Revised May 2003

SECTION 6.0 AUTOCALIBRATION OF ACCELERATOR

POTENTIOMETERS

When calibrating the right and left throttle potentiometers

(for standard truck configuration), program Function 5 with

a handset to a value of 24, and then exit programming

mode. Cycle the key switch on and off to store the function

setting, and leave the handset plugged in.

When returning the key switch to the “ON” position, make

sure that the seat switch is open, and both the left and right

accelerator pedals are fully released. Once all of the above

conditions have been met, four “A” ’s will appear on the

handset.

AAAA

When the four “A” ’s are displayed, close the seat switch,

with the accelerator pedals fully released to calibrate the

potentiometers to this position. The dash display should

show three “A” ’s:

AAA

Re-open the seat switch to begin the calibration of the fully

depressed right accelerator pedal position. Depress the

right accelerator pedal fully, and close the seat switch to

calibrate the fully depressed right accelerator pedal. When

this is completed, the dash display should show two “A” ’s:

Re-open the seat switch to begin the calibration of the fully

depressed left accelerator pedal position. Depress the left

accelerator pedal fully, and close the seat switch to

calibrate the fully depressed left accelerator pedal. When

this is completed, the dash display will return to normal

operation. Confirm this by opening the seat switch, and the

dash display will show “-01

The autocalibration routine is now completed.

----

If truck operation with the forward and reverse switches is

desired (optional configuration), set Function 5 to a value of

152. With the key switch in the “OFF” position, the seat

switch open, and both the forward and reverse switches in

the neutral position, turn the key switch to “ON” and the

dash display will show four “A”’s:

AAAA

To calibrate the right fully released accelerator pedal

position, leave the pedal fully released and close the seat

switch. When this calibration is completed, the display will

show three “A”’s:

AAA

Re-open the seat switch and fully depress the right

accelerator pedal. Close the seat switch to complete the

calibration of the fully depressed pedal. The dash display

will then return to normal operation. Confirm this by

opening the seat switch, and the dash display will show

“01”.

The autocalibration routine is now completed.

Содержание SX Series






































































Результаты поиска

Содержание SX Series

Отзывы:

Похожие инструкции для SX Series

Бренды по названию

Популярные бренды

GE SX Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SX Series

Отзывы:

Похожие инструкции для SX Series

Бренды по названию

Популярные бренды