GE SX Series Скачать руководство пользователя

Страница: 63 / 69

ADJUSTABLE FEATURES

TRANSISTOR PUMP CONTROLS

Page

Revised May 2003

Section 5.6 Setup Functions for Hydraulic Pump Control

FUNCTION 1:

NOT APPLICABLE

This function is not applicable to this type of control and

should not be adjusted.

FUNCTION 2:

PERCENT ON-TIME ADJUSTMENT

(Push

This function allows for the adjustment of the percent on-

time of the control.

Range

2 – 15% on-time

Setting

0 - 255

Resolution 0.05% per set unit

Example:

Setting of 20 = (20 x 0.05) + 2 = 3%

FUNCTION 3:

CONTROLLED ACCELERATION

(Push

This function allows for the adjustment of the rate of time it

takes for the control to accelerate to 96% applied battery

voltage to the motor on hard acceleration.

Range

0.1 to 5.5 seconds

Setting

0 to 255

Resolution

0.021 seconds per set unit

Example: Setting of 20 = 0.52 seconds C/A

FUNCTION 4:

CURRENT LIMIT

(Push

This function allows for the adjustment of the current limit

of the control. The rating of the control will determine the

range of adjustment for this function. Please refer to the

OEM operating instructions for the control used in your

vehicle.

Range

See OEM control C/L curves

Setting

0 to 255

Example: 0 = min. current, 255 = max. current

FUNCTION 7:

NOT APPLICABLE

This function is not applicable to this type of control and

should not be adjusted.

FUNCTION 11:

SPEED LIMIT 1 (SL1)

(Push

11)

This function allows for the adjustment of the speed limit

(maximum battery volts to the motor) when the SL1 limit

switch input signal is received by the control card. SL1

limit switch is a normally open switch connected to battery

negative, the switch closing enables speed limit.

Range

0% to 100% battery volts

Setting

0 to 255

Resolution

0.375 volts per set unit

Example: Setting of 50=18.75 volts

FUNCTION 12:

SPEED LIMIT 2 (SL2)

(Push

12)

Same as Function 11 except using SL2 limit switch for input.

FUNCTION 13:

SPEED LIMIT 3 (SL3)

(Push

13)

Same as Function 11 except using SL3 limit switch for input.

FUNCTION 14:

SPEED LIMIT 4 (SL4)

(Push

14)

Same as Function 11 except using SL4 limit switch for input.

FUNCTION 16:

NOT APPLICABLE

This function is not applicable to this type of control and

should not be adjusted.

FUNCTION 17: CARD TYPE SELECTION

(Push CONT 2)

This function should be set in accordance with the control

type in use in the vehicle:

Function

Without Pump Ctr/PMT

High C/L

BDI Lockout

63 - 71

Note: The following functions have function numbers
larger than the numbers on the Handset keyboard. To
access these functions, push the CONT key and the
number shown in the following instructions at the same
time. THE KEY SWITCH MUST BE OPEN.

Содержание SX Series






































































Результаты поиска

Содержание SX Series

Отзывы:

Похожие инструкции для SX Series

Бренды по названию

Популярные бренды

GE SX Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SX Series

Отзывы:

Похожие инструкции для SX Series

Бренды по названию

Популярные бренды