GE SX Series Скачать руководство пользователя

Страница: 30 / 69

DIAGNOSTIC STATUS CODES

SX TRANSISTOR CONTROL

Page

Revised May 2003

TRACTION

STATUS CODE

DESCRIPTION OF STATUS

CAUSE OF STATUS INDICATION

-28

Motor field current is too high during
the run mode.

This status code will be displayed when the current in
the motor field is sustained above a preset limit for
longer than 70 seconds.

MEMORY RECALL

YES

CORRECTIVE ACTIONS

TROUBLE-SHOOTING DIAGRAM

Circuits valid

for

Traction

Controller

SYMPTOM

Control will not operate.

POSSIBLE CAUSE

Continued operation of vehicle in high
motor current condition.

Operate vehicle at lower motor
current condition for 70 seconds.

Function 7 is mis-adjusted to allow
higher than normal motor field current.

Adjust function per OEM
instructions.

THE PRESENCE OF THIS STATUS CODE

IS NOT NECESSARILY INDICATIVE OF A

CONTROL ISSUE. IF FUNCTION 7 IS NOT

MIS-ADJUSTED, THE STATUS CODE
INDICATES AN APPLICATION ISSUE

WHERE A MOTOR IS BEING STALLED,

ETC. DISPLAY OF THIS STATUS CODE

SHOULD NOT TRIGGER THE RETURN OF

A CONTROL FOR REPAIR OR

REPLACEMENT.

TRACTION

STATUS CODE

DESCRIPTION OF STATUS

CAUSE OF STATUS INDICATION

-41

Open thermal protector (TP) or
transistor over temperature.

This status code will be displayed when the voltage at
the thermal protector is too high.

MEMORY RECALL

YES

CORRECTIVE ACTIONS

TROUBLE-SHOOTING DIAGRAM

Circuits valid

for

Traction

Controller

SYMPTOM

Reduced or no power to traction motor
in control range.

POSSIBLE CAUSE

Control is in thermal cut-back.

Allow control to cool, status code
should disappear.

Defective control.

Replace controller unit.

THE PRESENCE OF THIS STATUS CODE

IS NOT NECESSARILY INDICATIVE OF A

CONTROL ISSUE. THE STATUS CODE

MAY INDICATE AN APPLICATION ISSUE

WHERE A MOTOR IS BEING STALLED,

ETC. DISPLAY OF THIS STATUS CODE

SHOULD NOT TRIGGER THE RETURN OF

A CONTROL FOR REPAIR OR

REPLACEMENT.

Содержание SX Series






































































Результаты поиска

Содержание SX Series

Отзывы:

Похожие инструкции для SX Series

Бренды по названию

Популярные бренды

GE SX Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SX Series

Отзывы:

Похожие инструкции для SX Series

Бренды по названию

Популярные бренды