GE SIMON XT Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 63

background image

Installation

Tabs at the top of the panel secure and release the front cover and the chassis. The
plastic hinges on the panel bottom allow the cover and chassis to swing down and
out of the way.

To mount the panel on a wall:

1. Choose a panel location and run all necessary power, phone, siren, and hardwired

contact wires to the desired location.

When choosing the AC outlet location for the AC power transformer, make sure
the outlet is not controlled by a switch or that it is not part of a ground fault circuit
interrupt (GFCI).

2. Hold the panel against the wall and mark the mounting hole locations with a

pencil (see Figure 3 below).

3. Mount the back piece to the wall through the two horizontally centered mounting

holes near the top and bottom using the supplied mounting hardware. Use wall
anchors if no studs are present.

4. Connect the chassis assembly to the mounted back piece and let it hang down.

This makes the terminal strip accessible for wiring various hardwired components
to the panel.

5. Feed wires through opening in the back piece to be ready to attach them to the

screw terminals or the phone connectors.

6. Install all screws and tighten gently.

Figure 3: Mounting holes

Mounting hole

Mounting hole

Wiring knockout

14

Simon XT Installation Manual

«
...
16
17
18
19
20
...
»

Содержание SIMON XT
































































Отзывы:

Нет отзывов

Похожие инструкции для SIMON XT

Бренд: GBD Страницы: 12

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

Бренд: PACH & COMPANY Страницы: 4

Бренд: Raypak Страницы: 24

Бренд: J+J Страницы: 91

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

Бренд: Vacon Страницы: 40

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 26

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA SIEMENS Страницы: 373

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды