background image

GE Consumer & Industrial

Appliances

Installation Instructions

Built-In Dishwasher

If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com

imagination at work

IMPORTANT

 

– The dishwasher MUST

be installed to allow for future removal from the enclosure
if service is required.

If you received a damaged dishwasher, you should
immediately contact your dealer or builder.

Optional Accessories – See the Owner’s Manual for available 
custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS

shown throughout these instructions. While performing 

installations described in this booklet, gloves and either  

safety glasses or goggles should be worn.

PDW8400JWW/BB/CC

ANTI

BACTER

IA

START
RESET

TO LOCK

 CONTRO

LS

PRESS H

EATED D

RY

FOR 3 SE

CONDS

ENHANC

EMENTS

SELECTI

ONS

SENSING

WASHIN

G RINS

ING

DRYING

SANITIZ

ED

CLEAN

COOK

WARE

NORMA

L

WASH

SPEED

CYCLE

CHINA

CRYSTA

L

RINSE

ONLY

2  4  8

DELAY

HOURS

ADDED

HEAT

PRE

WASH

HEATED

DRY

READ CAREFULLY. 

KEEP THESE INSTRUCTIONS.

PDW8200 Series 

PDW9200 Series

PDW8400 Series 

PDW9700 Series*

PDW8700 Series 

PDW9800 Series 

PDW8800 Series 

PDW9900 Series

PDW8900 Series

* For PDW9700 Series also refer to the Instructions  

provided on the template packed with that model. 
(WD35X1005)

IMPORTANT

 

– Observe all governing codes and 

ordinances.
• 

Note to Installer

 – Be sure to leave these instructions for the 

consumer’s and local inspector’s use.

• 

Note to Consumer

 – Keep these instructions with your 

Owner’s Manual for future reference.

• 

Skill Level

 – Installation of this dishwasher requires 

basic mechanical, electrical and plumbing skills. 

Proper 

installation is the responsibility of the installer. Product 

failure due to improper installation is not covered under 

the GE Appliance Warranty. See warranty information.

• 

Completion Time – 1 to 3 Hours

. New installations require 

more time than replacement installations.

STOP

BEFORE YOU BEGIN

Read these instructions completely and
carefully.

Содержание Profile PDW8680N


















Отзывы: