background image

Installation Instructions

STEP 18 DISHWASHER WET TEST

  Turn on power supply (or plug power cord into outlet,  

if equipped).

  Start the unit to check for leaks. 

PDW8200-PDW8900 Series: 

– Latch door 
– Push RINSE ONLY pad 
– Push START/RESET pad one time 

PDW9200-PDW9900 Series:

 

– Push RINSE ONLY pad 
– Push START/RESET pad one time 
– Close door

  Check to be sure that water enters the dishwasher. If water 

does not enter the dishwasher, check to be sure that water 
and power are turned on.

  Check for leaks under the dishwasher. If a leak is found, turn 

off power supply, then tighten connections. Restore power 
after leak is corrected.

  Check for leaks around the door. A leak around the door 

could be caused by door rubbing or hitting against  
adjacent cabinet. Reposition the dishwasher if necessary. 
See Step 11.

  The dishwasher will drain and turn off about 5 minutes after 

it was started. Check drain lines. If leaks are found, turn off 
power at the breaker and correct plumbing as necessary. 
Restore power after corrections are made. See Step 8  
and 15.

  Open dishwasher door and make sure most of the water 

has drained. If not, check that disposer plug has been 
removed and/or air gap is not plugged. See Step 15. Also 
check drain line for kinking.

  Run the dishwasher through another “Rinse Only” cycle. 

Check for leaks and correct if required.

Figure LL

STEP 19  REPLACE TOEKICK BRACE AND 

TOEKICK

• Replace toekick brace and attach with screws set aside 

in Step 4 (the lower set of mounting holes may be used if 
desired). Only for PDW9700 series and PDW9900 series.

• Place toekick against the legs of the dishwasher.

���������

����������

������

�������

• Align the toekick with the bottom edge and make sure it is 

against the floor.

• Insert and tighten the 2 toekick attachment screws. The 

toekick should stay in contact with the floor.

Tip:

 Make sure toekick is against floor to minimize noise.

STEP 20 LITERATURE

• Be sure to leave complete literature package and Installation 

Instructions with the consumer.

���������

����������

������

�������������

Figure MM

Содержание Profile PDW8680N


















Отзывы: