GE PAC8000 series Скачать руководство пользователя | Manualshive

Страница: 31 / 50

background image

Index

GFK-2839B

PAC8000* IO PROFINET Scanner

User’s Manual–September 2017

31

Chapter 3.

Configuration

This chapter provides general information for configuring a PAC8000 PNS and its IO modules
in a PROFINET-IO network. For information on configuring the PROFINET IO-Controller and
its network, refer to the IO-

Controller manufacturer’s documentation.

Note:

To configure RX3i Controller, refer to the

PACSystems RX3i PROFINET Controller

Manual,

GFK-2571.

This chapter discusses the following topics:

■

Configuration Overview

o

Basic Configuration Steps

o

Configuration Tool

■

Adding a PAC8000 PROFINET Scanner to a LAN

o

Configuring PAC8000 PROFINET Scanner Parameters

o

Configuring PAC8000 Module Parameters

■

Assigning IO-Device Names

■

Clearing the PROFINET IO-Controller Configuration

■

Replacing PAC8000 PROFINET Scanner Hardware

3.1

Configuration Overview

The PAC8000 PNS receives its configuration from a PROFINET IO-Controller, which is
configured by a PROFINET IO configuration tool. The GSDML file provided with the PNS
must be imported into the PROFINET IO configuration tool.

Note:

For details on using the

Proficy Machine Edition PLC Logic Developer

programmer to

create and download the configuration for a PAC8000 PNS in an RX3i PROFINET
network, refer to the

PACSystems RX3i PROFINET IO-Controller Manual,

GFK-2571.

«
...
29
30
31
32
33
...
»

Содержание PAC8000 series



















































Отзывы:

Нет отзывов

Похожие инструкции для PAC8000 series

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

Бренд: K&K Страницы: 6

Бренд: Eaton Страницы: 86

Бренд: KAR-TECH Страницы: 28

Бренд: 2M Technology Страницы: 17

Бренд: 2iB Страницы: 5

Go!Control Panel

Бренд: 2gig Technologies Страницы: 78

Бренд: LAS Страницы: 6

Бренд: Saftronics Страницы: 13

Бренд: Eaton Страницы: 96

Бренд: TCi Страницы: 9

Бренд: Klimaire Страницы: 5

Бренд: Hunter Страницы: 2

Бренд: Tektronix Страницы: 112

Бренд: MX Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды