GE PAC8000 series Скачать руководство пользователя

Страница: 22 / 50

Contents

PAC8000* IO PROFINET Scanner

User’s Manual–September 2017

GFK-2839B

2.3

Installation in Hazardous Areas

The following information is for products bearing the UL marking for Hazardous
Locations or ATEX marking for explosive atmospheres:

•

EQUIPMENT LABELED WITH REFERENCE TO CLASS I, DIVISION 2, GROUPS A,
B, C & D, HAZARDOUS LOCATIONS (ALTERNATIVELY MARKED AS CLASS I
ZONE 2, GROUP IIC) IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS
A, B, C, D OR NON-HAZARDOUS LOCATIONS ONLY

▪

Equipment labeled with

II 3 G is suitable for use in Group 2 Category 3

environments.

▪

Connectors P1, J101 & HVCC shall be secured properly with the mechanical latch
provided for the purpose.

•

WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY
IMPAIR SUITABILITY FOR CLASS I, DIVISION 2;

•

WARNING - EXPLOSION HAZARD - WHEN IN HAZARDOUS LOCATIONS, TURN
OFF POWER BEFORE REPLACING OR WIRING MODULES; AND

•

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT
UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE
NONHAZARDOUS.

•

WARNING - EXPLOSION HAZARD - USB PORT IS ONLY FOR USE IN

NONHAZARDOUS LOCATIONS, DO NOT USE UNLESS AREA IS KNOWN TO BE
NON-HAZARDOUS.

2.3.1

ATEX Marking

II 3 G Ex nA IIC T5 -40ºC



+70



(Ref. ATEX Cat-3 certificate# GE13ATEX8515X & GE13ATEX8516X from our support
website for details of marking and installation guidelines.)

2.3.2

CE Marking

CE (EMC & ATEX Directives)

(Ref. Declaration of Conformity from our support website for details)

UL Marking

LISTED FOR US and CANADA FOR HAZLOC & PROCESS

CONTROL INSTRUMENTS CATEGORY

HAZLOC Classification

Class I Zone 2 Group IIC

Alternate Classification: Class I Division 2 Groups A, B, C, D

Содержание PAC8000 series



















































Результаты поиска

Содержание PAC8000 series

Отзывы:

Похожие инструкции для PAC8000 series

Бренды по названию

Популярные бренды

GE PAC8000 series, Руководство пользователя

Результаты поиска

Содержание PAC8000 series

Отзывы:

Похожие инструкции для PAC8000 series

Бренды по названию

Популярные бренды