GE Optima XR220amx Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 92

background image

Chapter 2: Safety and Regulatory

Optima XR220amx X-Ray System

54400222-1EN

Rev 1 DRAFT 11092010

2-15

Operator Manual

© 2010 General Electric Company. All rights reserved.

Collimator

The table below describes the collimator controls and the radiation field.

Noiseless (clean) earth (ground) identifies any terminal of a specially designed
earthing system where noise from earth of leads will not cause a malfunction of
the equipment.

Protective earth (ground) identifies any terminal which is intended for
connection of an external protective conductor to protect against electrical
shock in case of a fault.

Frame or chassis identify the frame or chassis terminal.

Equipotentiality identifies terminals that bring the various parts of equipment or
systems to the same potential when connected together. These terminals are
not necessarily at earth (ground) potential. The value of the potential may be
indicated next to the symbol.

Table 2-8

Collimator descriptions

Symbol

Description

Control for indicating radiation field by using light.

Identifies controls for opening the collimator blades, or indicates partially or fully
open state.

Identifies controls for closing the collimator blades, or indicates closed state.

Indicates the collimator blades are closed. The controlled blades are shown in
thicker lines.

Table 2-7

Ground types

Symbol

Description

DRAFT

REVIEW COPY

CTRL+SHIFT+F to search using Search Index (faster)

«
...
24
25
26
27
28
...
»

Содержание Optima XR220amx





























































































Отзывы:

Нет отзывов

Похожие инструкции для Optima XR220amx

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Abu Garcia Страницы: 6

Бренд: Panlux Страницы: 2

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды