manualshive.com logo in svg
background image

508133G01 / 31-5000715

Page 17 of 25

Issue 2140

Outdoor Unitary Control

Jumpers and Terminals

RAST TERMINALS FOR 

THERMOSTAT WIRING 

CONNECTION

CHARGE MODE AND 

OPERATION MODE

JUMPER DETAIL

PUSH BUTTON

7 SEGMENT 

DISPLAY

OPERATION 

MODE 

JUMPER

CHARGE 

MODE JUMPER

(CHRG MODE)

Figure 11.  

7-Segment Display and Push Button

Information labels concerning the outdoor control 

7-segment display and push button operations are 

available on the unit control panel cover.

Alarms

Alarm information is provided on the unit control panel 

cover.

Programing Unit Type

Programming to the appropriate tonnage allows the unit to 

operate in the range of compressor and fan speeds that 

are optimized for best unit performance and efficiency. 

The  NS18HMA  units are programmed from the factory 

to function in 3 Ton and 5 Ton modes of operation. If the 

intended capacity for the application is 3 or 5 Ton, skip this 

section.

The units are field convertible to 2 Ton or 4 Ton to efficiently 

perform for the required application. If the intended capacity 

is 2 or 4 Ton, proceed to the following steps to program the 

unit type. Outdoor unit must be powered ON and in idle 

mode (no heating or cooling mode of operation). 

NOTE: 

The -36 unit can be programmed to operate as a 

2 Ton, and the -60 unit can be programmed to operate as 

a 4 Ton.

Perform the following steps to program the unit type.
1.  To enter mode options, push and hold the push button 

next to the seven-segment display until a DASH (-) 

symbol appears. Immediately release the button. Once 

the dash starts blinking, proceed to the next step.

_

2.  Push and hold button again until 

PU

 is displayed on 

the seven-segment display. Immediately release the 

button.

PU

3.  Push and hold button until the code for the correct unit 

type is displayed.

Unit Code

Unit Type

58

2 Ton

60

3 Ton

62

4 Ton

63

5 Ton

Table 8. Unit Tonnage Codes

Содержание NS18HMA


























Отзывы: