manualshive.com logo in svg

GE NetworX NX-6V2, Установка и запуск

GE NetworX NX-6V2 - надежная система безопасности для вашего дома. Установите и настройте ее самостоятельно, следуя инструкциям по установке в руководстве. Скачайте руководство бесплатно с нашего сайта, чтобы получить подробные сведения о настройке и функциях продукта. manualshive.com.

Поделиться
Скачать
background image

 

NX-6V2 Control 

 

19 

Segment 4:

 

1 =  On if Fail To Communicate report enabled. 
2 =  On if Log Full report enabled. 
3 =  On if Autotest report enabled. 
4 =  On if Start/End programming report enabled. 
5 =  On if End Download report enabled. 
6 =  On if Sensor Low Battery report enabled. 
7 =  On if Sensor Missing report enabled. 
8 =  On if First to Open / Last to Close. 

 

Segment 5: 

 

1 =  On enable Lost Clock service light. 
2 =  On enables Zone Doubling (requires NX-200 Zone Doubling Kit). 
3 =  On disables On-Board 6 zones. 
4 =  On will allow two trips on same cross-zone to activate an alarm. 
5 =  On will 

not

 allow zones that are force armed to report bypass. 

6 =  Reserved. 
7 =  Use internal crystal for clock.  
8 =  Disable Temporal Siren on Fire. NOTE: Do NOT disable for UL listed systems. 

 
Segment 6:

 

 

1 =  Enable 2 wire smoke. 
2 =  Reserved. 
3 =  Enable for Zone Activity in Hours (not Days) 
4 =  Enable Daylight Savings Time (DST)  
5 =  Reserved 
6 =  On to disable Clean Me report (At default, bit is OFF = enabled) 
7 =  On to disable Start/End Test report (At default, bit is OFF = enabled) 
8 =  Reserved. 

 

Segment 7:

 Reserved 

 

L 

38 SWINGER 

SHUTDOWN 

COUNT 1............. numerical 

Location 38 contains the number of trips during an arming cycle that the NX-6V2 will allow before bypassing a zone. The count 
determination is described in the Glossary. 

Factory default is 1.

 

 

L

 

39 

KEYPAD SOUNDER CONTROL 1............. feature 

select 

Segment 1:

 

 

1 =  On if keypad sounds for 

A

Telephone Line Cut

@

 when the system is armed. 

2 =  On if keypad sounds for 

A

Telephone Line Cut

@

 when disarmed. 

3 =  On if keypad sounds upon AC Power Failure. 
4 =  On if keypad sounds when a Low Battery is detected. 
5 =  On if keypad sounds during Cross Zone trip time. 
6 =  On if keypad sounds for zone and box tampers. 
7 =  Reserved. 
8 =  On if keypad sounds for expander trouble (required for UL installations). 

 

L 

40 SYSTEM 

TIMERS 

14........... numerical 

Location 40 contains the duration of various system timing functions.  Example: If you desire the duration of the Dynamic Battery Test 
to be 30 minutes, you should program [3]-[0]-[

r

] in segment 1 of this location.  The [3]-[0] is the number of minutes, and the [

r

] stores 

the data and moves to the next segment of this location. 
 

NOTES FOR UL INSTALLATIONS 

The "Listen-In" feature cannot be enabled for UL Listed systems. 
The "Dynamic Battery Test" feature cannot exceed four (4) hours. 
The dial delay shall be set to -0-. 

 

Segment 1 

-  

Dynamic Battery Test duration in minutes 0-255 minutes ..................................... (0 = no test) 

Segment 2

  - 

AC Fail report delay in minutes 0-255 minutes. .................................................... (0 = no delay) 

Segment 3

 - 

Power Up Delay in seconds 0-60 seconds ........................................................... (0 = no power up delay) 

Segment 4

 -  

Siren Time in minutes 1-254 minutes. 

Segment 5

 -  

Telephone Line Cut delay in seconds 0-255 seconds........................................... (0 = no TLM) 

Segment 6

 -  

Cross Zone time in minutes 0-255 ........................................................................ (0 = no cross zoning)  

Segment 7

 -  

Chime time in 50 mS (1/20th second) increments from 0-12 seconds.................. (0 = follows zone 255 latched) 

Segment 8

 - 

Dial delay in seconds 15-255 seconds 

Содержание NetworX NX-6V2





















































Отзывы:

Нет отзывов

Похожие инструкции для NetworX NX-6V2

Eaton AMPGARD RVSS Instruction For Installation And Maintenance preview
AMPGARD RVSS
Бренд: Eaton Страницы: 16
Daikin Maverick I Operation Manual preview
Maverick I
Бренд: Daikin Страницы: 48
Daikin MicroTech III Operating Manual preview
MicroTech III
Бренд: Daikin Страницы: 77
Daikin MicroTech III Operation And Maintenance Manual preview
MicroTech III
Бренд: Daikin Страницы: 32
Daikin BRC1E71 Engineeiring Data preview
BRC1E71
Бренд: Daikin Страницы: 46
Daikin MicroTech III Installation And Maintenance Manual preview
MicroTech III
Бренд: Daikin Страницы: 14
Daikin DCS601C51 Hardware Manual preview
DCS601C51
Бренд: Daikin Страницы: 16
Daikin BRC944B2 Quick User Manual preview
BRC944B2
Бренд: Daikin Страницы: 1
fakro ZWMA Programming And Usage Instructions preview
ZWMA
Бренд: fakro Страницы: 16
e-BLEACH infinity User Manual preview
infinity
Бренд: e-BLEACH Страницы: 24
ICM Controls ICM325HN Installation, Operation & Application Manual preview
ICM325HN
Бренд: ICM Controls Страницы: 2
Nedap WIM Installation Manual preview
WIM
Бренд: Nedap Страницы: 20
Lab.gruppen LAB.LEVEL4 Quick Start Manual preview
LAB.LEVEL4
Бренд: Lab.gruppen Страницы: 2
J+J J4C 20 Assembly Instructions Manual preview
J4C 20
Бренд: J+J Страницы: 6
Waeco Switch200VTO Installation And Operating Manual preview
Switch200VTO
Бренд: Waeco Страницы: 168
Hanma HM-R01-RC Instructions preview
HM-R01-RC
Бренд: Hanma Страницы: 3
Zonex DIGI3U Installation Manual preview
DIGI3U
Бренд: Zonex Страницы: 16
FAAC B614 Translation Of The Original Instructions preview
B614
Бренд: FAAC Страницы: 63

Бренды по названию

Популярные бренды

Загрузить еще бренды