60
5.2.43.3 Remove timer control knob (Section 5.2.41).
5.2.43.4 Remove the dress panel LH side (Section 5.2.44).
5.2.43.5 Remove the dress panel RH side (Section 5.2.45).
5.2.43.6 Remove the 3 steel screws located at the front of
the steel control panel.
5.2.43.7 Bend the 2 side metal retaining lugs to a vertical
position.
5.2.43.8 Slide the carrier panel out of the steel control panel.
5.2.43.9 Reassemble the dishwasher in reverse order.
5.2.43.10 Operate and test the dishwasher before leaving.
5.2.44 Dress Panel LH Side - 5600 model
5.2.44.1 To remove the dress panel LH side cover, first
remove the control panel (Section 5.2.40).
5.2.44.2 Unlatch the bottom clip from the back of the carrier
panel. Push forward and withdraw the dress panel from the
face of the control panel by pulling it out, down and away.
This disengages the 2 locking toes from the recesses in the
top of the steel control panel.
5.2.44.3 To reinstall, locate the 2 top locking toes and clips
first, then push the panel firmly in, locking the bottom clip in
place.
5.2.44.4 Reassemble the dishwasher in reverse order.
5.2.44.5 Operate and test the dishwasher before leaving.
5.2.41 Timer Control Knob - 5600 model
5.2.41.1 Prior to removing the timer control knob, advance
the timer control knob pointer to the twelve o’clock position
(“OFF” position). The timer control knob can then be
removed by pulling the knob straight towards you and
removing it from the timer control shaft.
5.2.41.2 To reinstall the timer control knob, align the four
flutes of the timer control shaft with the four slots in the timer
control knob and push the timer control knob onto the shaft
securely.
NOTE: The nylon shaft of the timer control has three large
flutes positioned at twelve o’clock, three o’clock and nine
o’clock. A smaller fourth flute is positioned at six o’clock.
Identify the four slots in the timer control knob and index
accordingly to assist in reinstalling.
5.2.42 Power Select Knob - 5600 model
5.2.42.1 To remove the power select knob, grasp the knob
and pull from the rotary switch shaft.
NOTE: If the power select knob is removed with the knob
pointer indicating an “OFF” position, the flat on the switch
shaft is vertical and on the left hand side of the shaft.
5.2.42.2 To reinstall the power select knob, note the position
on the rotary switch shaft and align the power select knob.
Push on to the shaft securely.
5.2.43 Control Panel - 5600 model
The design of the 5600 model control panel is based on a
steel outer frame surrounding an inner plastic carrier panel,
to which dress panels, handle components and rotary
control components are attached. The following procedures
illustrate the disassembly of the complete control panel.
CAUTION. Switch off electrical power supply.
5.2.43.1 First remove the complete control panel (Section
5.2.40).
5.2.43.2 Remove the power select knob. (Section 5.2.42)
Содержание Monogram ZBD5600
Страница 1: ...g GE Consumer Service Training TECHNICAL SERVICE GUIDE ZBD5900 ZBD5700 ZBD5600 Dishwashers ...
Страница 70: ...69 6 5 Wiring Diagram 5700 5900 Models Important Check all wiring connections before reconnecting to supply ...
Страница 71: ...70 6 4 Sequence Chart 5600 Model ...
Страница 72: ...71 6 5 Wiring Diagram 5600 Model Important Check all wiring connections before reconnecting to supply ...
