GE Monitor UV-900 Скачать руководство пользователя страница 12

Страница: 12 / 46

Installation

Monitor UV-900 User Manual 18-1120-05 Edition AF

2.4

Connecting electrical signal cables

The sockets for electrical signals are located on the back panel.

2.4.1

Connecting to recorder (if used)

1 Connect the recorder to the miniDIN-socket

Analogue out

using the cable

supplied. Each wavelength signal is available on a separate channel using

the following wires:

Note:

The signal cable is delivered with protective covers on each wire. Do

not remove the protective covers from unused connections as a

short circuit may disturb the measurements.

2 Set the recorder to 0–1 V input, full scale, 0 V offset.

2.5

Connecting to communication link

The monitor can be used in ÄKTAexplorer or ÄKTApurifier and controlled from a

PC running UNICORN

™

version 3.21 or higher, using UniNet cables.

Analogue out

0-1V

Remote UniNet 1

Mains

On/off

Wire 1

Wire 2

–

Wire 3

Wire 4

Wire 5

Wire 6

CAUTION!

The mains power to the ÄKTAexplorer or ÄKTApurifier must be

switched OFF before connecting the instrument to the UniNet-1 link.

WARNING!

Only use mains cables delivered or approved by GE Healthcare.

WARNING!

Do not block the rear panel of the system. The mains power

switch must always be easy to access.

Содержание Monitor UV-900















































Результаты поиска

Содержание Monitor UV-900

Отзывы:

Похожие инструкции для Monitor UV-900

Бренды по названию

Популярные бренды

GE Monitor UV-900, Руководство пользователя

Результаты поиска

Содержание Monitor UV-900

Отзывы:

Похожие инструкции для Monitor UV-900

Бренды по названию

Популярные бренды