GE GLDT690J__BB Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 33

GE GLDT690J__BB Скачать руководство пользователя страница 9

– 9 –

Overview of Cycles

• After pressing the

START/RESET

button, all LED's will light, the digital display will show

88

, and the buzzer

will beep.

• The estimated cycle time will be displayed as a two-digit number. If the cycle time exceeds 99 minutes,

the seven segment display will show

2H

. If the cycle time is less than or equal to 99 minutes, the actual

estimated cycle time is displayed.

• The control makes an End-of-Cycle Alert for 1 second every 2 minutes (with a maximum of 4 beeps) for

any mode (regardless of whether delay was selected or not) after the end of any cycle.

•

Cancel/Change cycle

: After a cycle has started, open the door and hold the

Select

button down for 3

seconds. After 3 seconds, the machine will beep and the display will select the next cycle to the right. If
left on any cycle with the door closed, the machine will drain and start that new cycle automatically.

•

Delay Start

: Select 1 to 24 hours as the amount of time to delay the start of the cycle. This will be

displayed as

1H

,

2H

, etc. The delay start display never shows minutes.

• When the door is closed, the display will turn off after 3 minutes regardless of a time delay. Opening the

GRRUZLOOWXUQWKHGLVSOD\EDFNRQ'XULQJWKHF\FOHUXQWKHVHOHFWHGF\FOH/('ZLOOÀDVKRQRII

•

Two Step Start

: The dishwasher may be programed with the door open only. Press the Cycle button

until the desired cycle is selected. Press Start and close the door within 4 seconds. Failure to close the
door within 4 seconds will require Start to be pressed again and closing the door within 4 seconds.

•

Cycle Interruption

: If a cycle is interrupted, Start/Reset must be pressed and the door closed within four

seconds. The control will wait 10 seconds before resuming the cycle. If the door is not closed within 4

VHFRQGVWKHF\FOHZLOOQRWUHVWDUW7KHF\FOHDQGVWDUW/('·VZLOOÀDVKDQGWKHEHHSHUZLOOVRXQGHYHU\

minutes until the cycle is restarted or canceled.

• There is no Demo mode.

NOTE

: The door must be open for the keypads to operate. The keypad will appear to be inoperable with the

door in the latched position.

Sanitize Wash

&\FOHGH¿QLWLRQ

The

Sanitized

LED will only be turned on at the end of the sanitize wash cycle if the following two conditions

are met during the cycle:

1. An internal calculation the board makes based on several heat factors (tempe time).

2.

7KHZDWHUWHPSHUDWXUHLQWKH¿QDOULQVHLVJUHDWHUWKDQRUHTXDOWR)

7KHPD[LPXPWLPHIRUWKH¿QDOULQVHLQWKHVDQLWL]HZDVKF\FOHLVPLQXWHV,IERWKRIWKHDERYHFRQGLWLRQV
DUHPHWSULRUWRWKHPLQXWHOLPLWWKH¿QDOULQVHZLOOHQGLPPHGLDWHO\DQGERWKWKH6DQLWL]HGOLJKWDQG
&OHDQ/('ZLOOWXUQRQ,IHLWKHUFRQGLWLRQLVQRWPHWDWWKHHQGRIWKHPLQXWHOLPLWWKH¿QDOULQVHZLOOHQG

and the Sanitized light will not turn on.

SSD (Seven

Segment

Display)

«
...
7
8
9
10
11
...
»

Содержание GLDT690J__BB


































Отзывы:

Нет отзывов