GE GLDT690J__BB Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 33

GE GLDT690J__BB Скачать руководство пользователя страница 22

– 22 –

Water Inlet Valve

The water inlet valve is electronically controlled and

VROHQRLGRSHUDWHG7KHÀRZRIZDWHULVFRQWUROOHG
E\DUXEEHUÀRZZDVKHUFDSDEOHRIPDLQWDLQLQJD
ÀRZUDWHRIJDOORQVSHUPLQXWH

liters per minute) with incoming water pressure
of 20 to 120 PSI. The water valve is mounted on a
bracket located on the left side of the front brace.

The water valve has an approximate resistance
value of 1k ohms and is energized for

approximately

VHFRQGVGXULQJHDFK¿OO

Operation of the water valve can be checked by
using the service mode. (See

Service Mode

.)

Water Valve Removal

1. Disconnect

power.

2. Remove the outer door panel (see

Outer Door

Panel Removal

).

3. Remove the 2 Phillips head screws, washers,

and the access panel.

7. Remove the clamp and the outlet hose from the

valve.

4.

'LVFRQQHFWWKHZDWHUVXSSO\OLQHIURPWKH¿OO

valve inlet.

5. Remove the 2 Phillips head screws that hold the

bracket to the front brace.

6. Disconnect the 2 wires from the solenoid.

8. Remove the four 1/4 in. hex head screws and

WKH¿OOYDOYHIURPWKHEUDFNHW

127(

Ensure the O-ring is retained in the valve

upon reassembly.

&DXWLRQ

The clamp is easily damaged during

removal and should not be reused. Use the screw-
type hose clamp provided with the new valve.

Disconnect

Bracket

Inlet

Outlet Hose

Clamp

O-Ring

«
...
20
21
22
23
24
...
»

Содержание GLDT690J__BB


































Отзывы:

Нет отзывов