GE GLDT690J__BB Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 33

GE GLDT690J__BB Скачать руководство пользователя страница 16

– 16 –

PCB Assembly Removal

1. Disconnect the power supply to the dishwasher.

2. Remove the control panel (see

Control Panel

Removal

).

3. Remove the 2 Phillips head screws that attach

the PCB cover to the PCB.

4. Disconnect the wire harnesses from the PCB.

5. Remove the 2 Phillips head screws that attach

the PCB assembly to the housing.

Door Switch Assembly

The door switch assembly consists of two switches
activated by a spring-loaded plunger. One door
switch connects or disconnects the line (hot) side of
120 VAC. The other switch connects or disconnects
the neutral side of 120 VAC.

:$51,1*

Power remains applied to the controller

location at CN1, Pin 1 to 3, while the door is open
(unlatched).

When the door is in the closed position, the door
latch presses and holds down the switch plunger
on the door switch assembly. This action holds the

GRRU¿UPO\DJDLQVWWKHVHDODQGWKHQRUPDOO\RSHQ

contacts of the door switches are closed.

Door Switch Assembly Removal

1. Disconnect the power supply to the dishwasher.

2. Remove the control panel (see

Control Panel

Removal

).

3. Disconnect the 4 wiring harnesses from the door

switch.

4. Remove the 2 Phillips head screws that hold the

door switch assembly to the control panel.

7. Remove 2 Phillips head screws from the display

UI.

Disconnect

«
...
14
15
16
17
18
...
»

Содержание GLDT690J__BB


































Отзывы:

Нет отзывов