GE GLDT690J__BB Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 33

GE GLDT690J__BB Скачать руководство пользователя страница 19

– 19 –

Tub Gasket and Trim

The dishwasher tub seal prevents water leakage.

7KHVHDOLV¿WWHGLQDVHDOFKDQQHOWKDWOLQHVWKHULP

of the dishwasher tub.

Tub Seal and Trim Removal

1. Open the dishwasher door.

2. Remove the dishwasher tub seal by grasping

one end of the seal to peel it away from the seal
channel.

4. Reverse the above procedures to install.

NOTE

:

When installing the tub seal, make sure it is

VHDWHGSURSHUO\LQWKHVHDOFKDQQHO5XQD¿QJHU

over the seal to make sure it is smooth and even for
a proper seal. A correctly installed gasket will have
both ends of the gasket equally distant from the
bottom of the tub.

3. Remove the dishwasher trim by pulling the trim

straight off the lip of the tub.

Heating Element

The heating element maintains water temperature
during the wash and rinse cycles and heats the air
during the static dry cycle.

The heater has an approximate resistance value of
21 ohms.

Operation of the heating element can be checked
by using the service mode (see

Service Mode

).

Allow

one or two minutes before opening the dishwasher
door and note if heat is present.

Heating Element Removal

1. Remove the outer door panel (see

Outer Door

Panel Removal

).

2. Remove the bottom rack.

3. Remove the 2 Phillips head screws, washers,

and the access panel.

4. Remove the 2 Phillips head screws and lower the

water valve from the front brace.

5. Remove the 2 Phillips head screws and lower the

junction box from the front brace.

(

Continued next page

)

6. Remove the 6 Phillips head screws and the front

brace from the dishwasher.

Seal Channel

Tub Seal

Trim

Tub Lip

Front Brace

Water Valve

Junction Box

«
...
17
18
19
20
21
...
»

Содержание GLDT690J__BB


































Отзывы:

Нет отзывов