manualshive.com logo in svg

GE Custom 8000, Инструкция по эксплуатации, Страница: 31 / 41

Поделиться
Скачать
GE Custom 8000 Скачать руководство пользователя страница 31

GE Industrial Control Systems  GEEP-124-I           Copyright 1997,1998 The General Electric Company, USA

31

GEEP-124-I  Horizontal Induction Motor

WPI, Antifriction Bearing

TROUBLE - SHOOTING CHART

Trouble

Possible Cause

Action

Overheating (cont’d)

Insufficient oil

Add oil; if oil supply is very low,
drain, flush with clean oil, and refill.

Contamination in oil or
improper grade of oil

Drain the oil. Flush with clean oil, and
relubricate using oil viscosity specified
on nameplate.

Oil rings rotating slowly or not
rotating at all (if oil rings are
used).

Oil ring has worn spot, replace with
new ring.

Rings bent or otherwise
damaged in reassembling.

Replace oil rings.

Oil seals bound up or damaged.

Replace seals.

Bearings Noisy or
Vibrating

Defective bearings or rough
journal.

Replace bearings or resurface shaft.

(antifriction type).

Wrong-grade of grease

Remove old grease and relubricate
using grease recommended by this
Instruction Book.

Insufficient grease

Remove relief plug and regrease
bearing. Replace plug after ½ hour
running.

Too much grease

Remove relief plugs and let motor run
until excess grease is purged. Then
reinstall plug.

Defective or damaged bearing

Replace bearing.

Foreign material in grease.

Remove relief plug. Purge
contaminated grease from bearings.
Relubricate until only clean grease is
exiting relief plug.

Low insulation resistance

Moisture

Dry winding

or insulation failure.

Dirt

Clean winding

Conducting particles have
penetrated insulation.

Obtain expert help for repair.

DLCGEEP-124-I/000, Approved, 2016-11-11, CampinasDM

Содержание Custom 8000










































Отзывы:

Нет отзывов