GE Custom 8000 Скачать руководство пользователя

Страница: 30 / 41

GEEP-124-I Horizontal Induction Motor

WPI, Antifriction Bearing

TROUBLE - SHOOTING CHART

Trouble

Possible Cause

Action

Noise or vibration
(cont’d)

Misalignment

Check parallel, angular and axial
alignment.

Air gap not uniform. (Machines
furnished without one bearing)

Center the rotor.

Noisy ball bearings

Check lubrication. Replace bearings if
noise is persistent and excessive.

Loose on foundation

Realign machine. Tighten hold-down
bolts.

Foreign material inside unit

Clean inside for unit.

Shorted field turns
(synchronous)

Check impedance of each pole.
Determine if one pole has noticeable
difference.

Overheating

Overloaded

Measure loading with ammeter and
compare with full load current on
nameplate. Reduce load.

Electrical load unbalance

Check for voltage unbalance or single
phasing.

Restricted ventilation

Clean filters, air passages and
windings. Check water cooling if
applicable.

Incorrect voltage and frequency.

Check nameplate values with power
supply. Also check voltage at terminals
with machine under full load.

Stator winding shorted. (line-to-
line)

Inspect winding for damage. Obtain
expert help for repair.

Stator winding ground.
(line-to-ground)

Inspect winding for damage. Obtain
expert help for repair.

Incorrect field current
(synchronous)

See nameplate - apply correct field.

Incorrect speed

Check speed, compare with nameplate.

Bearings overheating
(journal type)

Alignment

Check parallel, angular and axial
alignment. Correct as required.

DLCGEEP-124-I/000, Approved, 2016-11-11, CampinasDM

Содержание Custom 8000










































Результаты поиска

Содержание Custom 8000

Отзывы:

Похожие инструкции для Custom 8000

Бренды по названию

Популярные бренды

GE Custom 8000, Инструкция по эксплуатации

Результаты поиска

Содержание Custom 8000

Отзывы:

Похожие инструкции для Custom 8000

Бренды по названию

Популярные бренды