GE AKTAprocess Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 180

GE AKTAprocess Скачать руководство пользователя страница 8

Prerequisites

In order to operate ÄKTAprocess safely, and according to the intended purpose, the fol-
lowing prerequisites must be met:

•

You should be acquainted with the use of bioprocessing equipment and with the
handling of biological materials.

•

You must read and understand the Safety chapter of these Operating Instructions.

•

The system must be installed according to the instructions in Chapter 4 Installation,
on page 81.

•

A working knowledge of UNICORN™ software is required. Refer to the UNICORN
manuals for instructions on the software structure and the work flow.

Safety notices

This user documentation contains WARNINGS, CAUTIONS and NOTICES concerning the
safe use of the product. See definitions below.

Warnings

WARNING

WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury. It is important not to proceed
until all stated conditions are met and clearly understood.

Cautions

CAUTION

CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury. It is important not to pro-
ceed until all stated conditions are met and clearly understood.

Notices

NOTICE

NOTICE indicates instructions that must be followed to avoid
damage to the product or other equipment.

8

ÄKTAprocess Operating Instructions 29-0252-49 AA

1 Introduction

1.2 Important user information

«
...
6
7
8
9
10
...
»

Содержание AKTAprocess





















































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды